전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

SFSL5.5MDB 데이터시트(PDF) 8 Page - Yamar Electronics Ltd.

부품명 SFSL5.5MDB
상세설명  for DC-LIN Asynchronous Communication Over Noisy Lines
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  YAMAR [Yamar Electronics Ltd.]
홈페이지  http://www.yamar.com
Logo YAMAR - Yamar Electronics Ltd.

SFSL5.5MDB 데이터시트(HTML) 8 Page - Yamar Electronics Ltd.

Back Button SFSL5.5MDB Datasheet HTML 4Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 5Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 6Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 7Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 8Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 9Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 10Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 11Page - Yamar Electronics Ltd. SFSL5.5MDB Datasheet HTML 12Page - Yamar Electronics Ltd.  
Zoom Inzoom in Zoom Outzoom out
 8 / 12 page
background image
Proprietary and Confidential Information of YAMAR Electronics Ltd.
@ 2007 Yamar Electronics Ltd.
8
DS-SIG40 R1.8
0[4]
nAuto sleep
R/W
1 0 = Automatically enters into Sleep Mode
when no reception from the DC line for 8 Sec.
1
0[6:5]
For future use
00
0[7]
Interference
R
1 Interference Detected indication
-
1[5:0]
F0, F1, bit rate select R/W
6 See Tables 4.2 and 4.3
“FF”H
1[7:6]
For future use
Should be “11”
11
4.3
SIG40 Configuration
The SIG40 operates at default with the following parameters:
Bit rate: 19.2 kbps
F0=5.5MHz, F1=6.5MHz
The following configuration bits set the operating frequencies according to table 4.2.
Table 4.2 – F0, F1 select
Control_register1
(3:0)
F0
F1
0000
3.58Mhz
4.5Mhz
0001
3.58Mhz
5.5Mhz
0010
3.58Mhz
6Mhz
0011
3.58Mhz
6.5Mhz
0100
4.5Mhz
5.5Mhz
0101
4.5Mhz
6Mhz
0110
4.5Mhz
6.5Mhz
0111
4.5Mhz
Reserved
1000
Reserved
Reserved
1001
5.5Mhz
Reserved
1010
5.5Mhz
Reserved
1011
6Mhz
Reserved
1100
6Mhz
Reserved
1101
6.5Mhz
Reserved
1110
6.5Mhz
Reserved
1111
5.5Mhz
6.5Mhz
Table 4.3 – bit rates select
Control_register_1
(5:4)
01 = 57.6Kbps
10 =
Reserved
00 = 38.4Kbps
11 = 19.2Kbps
4.3.1
Command Mode
When in command mode, the host can configure the device according to the desired operating
parameters. The device enters command mode when pin HDC is lowered to zero. When in command
mode, data on the HDI pin is not transmitted to the bus, but is used to configure the SIG40. The
command can be written in any of the allowed Bit Rates.
In order to write to a control register, the host sends two bytes. The first byte begins with the address of
the register followed by 5(hex), and the second byte is the configuration data, as shown in figure 4.2.
The bytes should be sent more than 200nSec after lowering HDC.
Higher nibble [7:4]
Lower nibble [3:0]
First Byte
Register Address
5(hex)
Second Byte
Configuration Data
Configuration Data
Table 4.4 - Write Command
Figure 4.3 shows the pins involved in the writing process:



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com