| 전자부품 데이터시트 검색엔진 |
|
HT45B0K 데이터시트(PDF) 14 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT45B0K 데이터시트(HTML) 14 Page - Holtek Semiconductor Inc |
|
14 / 23 page ![]() Rev 1.00 March 22, 2010 14 HT45B0K SPI to USB Bridge 0: the data transfer from the endpoint FIFO to the MCU (MCU read data from the endpoint FIFO). 1: the data transfer from the MCU to the endpoint FIFO (MCU write data to the endpoint FIFO). This bit defines the direction of data transfer between the MCU and the endpoint FIFO. When the TX bit is set to high, this means that the MCU desires to write data to the endpoint FIFO. After the MCU write operation has been complete, this bit has to be cleared to zero before terminating FIFO request to indicate the end of data transfer. For a MCU read operation, this bit has to be cleared to zero to show that the MCU desires to read data from the endpoint FIFO and has to be set to high before terminating FIFO request to indicate the end of data transfer after the completion of MCU read operation. Bit 0 REQUEST: FIFO request control 0: no operation. 1: Request the desired FIFO. This bit is used to request the operation of the desired FIFO. After selecting the desired endpoint, the FIFO can be requested by setting this bit to high. After completion, this bit has to be cleared to zero. The MCU can communicate with the endpoint FIFO by setting the corresponding registers, whose addresses are listed in the following table. After reading the current data, the next data will show after 2μs, used to check the endpoint FIFO status and responds to the MISC register, if a read/write action is still being implemented. Some timing constrains are listed here. By setting the MISC register, the MCU can perform reading, writing and clearing actions. There are some examples shown in the following for the endpoint FIFO reading, writing and clearing. Read or Write FIFOn Table (n=0~5) Actions MISC Setting Flow and Status Check whether FIFOn can be read or not 00H → 01H → delay 2μs, check 41H (ready) or 01H (not ready) → 00H. Check whether FIFOn can be written or not 02H → 03H → delay 2μs, check 43H (ready) or 03H (not ready) → 02H. Read FIFOn sequence 00H → 01H → delay 2μs, check 41H → read* from FIFOn register and check not ready (01H) → 03H → 02H. Write FIFOn sequence 02H → 03H → delay 2μs, check 43H → write* to FIFOn register and check not ready (03H) → 01H → 00H. Read 0-sized packet sequence from FIFO0 00H → 01H → delay 2μs, check 81H → clear LEN0 (01H) → 03H → 02H. Write 0-sized packet sequence to FIFOn 02H → 03H → delay 2μs → 01H → 00H. Note *: There are 2μs existing between 2 reading actions or between 2 writing actions. R E Q U E S T R E A D Y T X R e a d F I F O T i m i n g R E Q U E S T R E A D Y T X W r i t e F I F O T i m i n g |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |