PIC16F616-HSLASHP datasheet(28/214 Pages) MICROCHIP

28 / 214 page

PIC16F610/616/16HV610/616

DS41288F-page 28

3.2

Clock Source Modes

Clock Source modes can be classified as external or

internal.

• External Clock modes rely on external circuitry for

the clock source. Examples are: Oscillator mod-

ules (EC mode), quartz crystal resonators or

ceramic resonators (LP, XT and HS modes) and

Resistor-Capacitor (RC) mode circuits.

• Internal clock sources are contained internally

within the Oscillator module. The Oscillator

module has two selectable clock frequencies:

4 MHz and 8 MHz

The system clock can be selected between external or

internal clock sources via the FOSC<2:0> bits of the

Configuration Word register.

3.3

External Clock Modes

3.3.1

EC MODE

The External Clock (EC) mode allows an externally

generated logic level as the system clock source. When

operating in this mode, an external clock source is

connected to the OSC1 input and the OSC2 is available

for general purpose I/O. Figure 3-2 shows the pin

connections for EC mode.

The Oscillator Start-up Timer (OST) is disabled when

EC mode is selected. Therefore, there is no delay in

operation after a Power-on Reset (POR) or wake-up

from Sleep. Because the PIC® MCU design is fully

static, stopping the external clock input will have the

effect of halting the device while leaving all data intact.

Upon restarting the external clock, the device will

resume operation as if no time had elapsed.

FIGURE 3-2:

EXTERNAL CLOCK (EC)

MODE OPERATION

3.3.2

OSCILLATOR START-UP TIMER

(OST)

If the Oscillator module is configured for LP, XT or HS

modes, the Oscillator Start-up Timer (OST) counts

1024 oscillations from OSC1. This occurs following a

Power-on Reset (POR) and when the Power-up Timer

(PWRT) has expired (if configured), or a wake-up from

Sleep. During this time, the program counter does not

increment and program execution is suspended. The

OST ensures that the oscillator circuit, using a quartz

crystal resonator or ceramic resonator, has started and

is providing a stable system clock to the Oscillator

module. When switching between clock sources, a

delay is required to allow the new clock to stabilize.

These oscillator delays are shown in Table 3-1.

TABLE 3-1:

OSCILLATOR DELAY EXAMPLES

OSC1/CLKIN

OSC2/CLKOUT(1)

I/O

Clock from

Ext. System

PIC® MCU

Note

Alternate pin functions are listed in the

Section 1.0 “Device Overview”.

Switch From

Switch To

Frequency

Oscillator Delay

Sleep/POR

INTOSC

4 MHz to 8 MHz

Oscillator Warm-Up Delay (TWARM)

Sleep/POR

EC, RC

DC – 20 MHz

2 Instruction Cycles

Sleep/POR

LP, XT, HS

32 kHz to 20 MHz

1024 Clock Cycles (OST)

PIC16F616-H/P 데이터시트(PDF) 28 Page - Microchip Technology

PIC16F616-H/P 데이터시트(HTML) 28 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL