MIC5353 datasheet(3/12 Pages) MICREL

3 / 12 page

Micrel, Inc.

MIC5353

May 2010

M9999-052510

Absolute Maximum Ratings(1)

Supply Voltage (VIN)..................................... −0.3V to +6.5V

Enable Input Voltage (VEN)................................−0.3V to VIN

Power Dissipation ..................................Internally Limited

(3)

Lead Temperature (soldering, 3sec).......................... 260°C

Storage Temperature (TS).........................−65°C to +150°C

ESD Rating

(4)................................................................. 2KV

Operating Ratings(2)

Supply Voltage (VIN) ...................................... +2.6V to +6.0V

Enable Input Voltage (VEN) ...................................... 0V to VIN

Junction Temperature (TJ) .......................... −40°C to +125°C

Junction Thermal Resistance

6-Pin 1.6mm x1.6mm Thin MLF

® (θJA) ...........92.4°C/W

Electrical Characteristics(5)

VIN = VOUT + 1.0V; COUT = 1.0µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C to +125°C, unless noted.

Parameter

Conditions

Min.

Typ.

Max.

Units

Variation from nominal VOUT

-2.0

+2.0

Output Voltage Accuracy

Variation from nominal VOUT; –40°C to +125°C

-3.0

+3.0

0.05

0.3

Line Regulation

VIN = VOUT + 1V to 6V; IOUT = 100µA

0.6

%/V

Load Regulation

IOUT = 100µA to 500mA

0.15

2.0

IOUT = 150mA

100

IOUT = 300mA

100

200

Dropout Voltage

(6)

IOUT = 500mA

160

350

Ground Pin Current

IOUT = 0 to 500mA

175

µA

Ground Pin Current in Shutdown

VEN ≤ 0.2V

0.01

µA

f = 1kHz; COUT = 1.0µF; CBYP = 0.1µF

Ripple Rejection

f = 20kHz; COUT = 1.0µF; CBYP = 0.1µF

Current Limit

VOUT = 0V

600

1100

1600

Output Voltage Noise

COUT = 1.0µF; CBYP = 0.1µF; 10Hz to 100kHz

µVRMS

Enable Input

Logic Low

0.2

Enable Input Voltage

Logic High

1.2

VIL ≤ 0.2V

0.01

Enable Input Current

VIH ≥ 1.2V

0.01

µA

Turn-on Time

COUT = 1.0µF; CBYP = 0.1µF

100

µs

Notes:

1. Exceeding the absolute maximum rating may damage the device.

2. The device is not guaranteed to function outside its operating rating.

3. The maximum allowable power dissipation of any TA (ambient temperature) is PD(max) = (TJ(max) – TA) / θJA. Exceeding the maximum allowable

power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.

4. Devices are ESD sensitive. Handling precautions recommended. Human body model 1.5KΩ in series with 100pF.

5. Specification for packaged product only.

6. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value measured at 1V

differential.

MIC5353 데이터시트(PDF) 3 Page - Micrel Semiconductor

MIC5353 데이터시트(HTML) 3 Page - Micrel Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

데이터시트 다운로드

링크 URL