ADS1258IPHPREP datasheet(35/57 Pages) TI

35 / 57 page

SCLK

DIN

Command Byte

(1) One or more bytes depending on MUL bit.

(2) After the prescribed number of registers are read, then one or more additional commands can be issued in succession.

NOTE:

SCLK

DIN

Command 1

Command 2(1)

Command 3(1)

NOTE: (1) One or more commands can be issued in succession.

ADS1258-EP

www.ti.com

SBAS445C – MARCH 2009 – REVISED DECEMBER 2009

Beginning

with

the

eighth

SCLK

rising

edge

(command byte completed), the MSB of the data is

To read register data, the first three bits of the

shifted in. The remaining seven SCLK rising edges

command byte to be shifted into the device are 010.

complete the write to a single register. If MUL = '1',

These bits are followed by the multiple register read

the data to the next register can be written by

bit (MUL). If MUL = '1', then multiple registers can be

supplying additional SCLKs. The operation terminates

read in sequence beyond the desired register. If

when the last register is accessed (address = 09h),

MUL = '0', only data from the addressed register can

as shown in Figure 60.

be read. The last four bits of the command word are

the beginning register address bits. During this time,

CONTROL COMMANDS

the invalid data may appear on DOUT until the

command is completed. This data should be ignored.

Pulse Convert Command

Beginning with the eighth falling edge of SCLK

(command byte completed), the MSB of the register

(See Conversion Control section)

data is output on DOUT. The remaining eight SCLK

transitions complete the read of a single register. If

Reset Command

MUL = '1', the data from the next register can be read

The Reset command resets the ADC. All registers

in sequence by supplying additional SCLKs. The

are reset to their default values. A conversion in

operation

terminates

when

the

last

process continues but is invalid when completed

accessed (address = 09h); see Figure 59.

(DRDY

low).

This

conversion

data

should

discarded. Note that the SPI interface may require

reset for this command, or any command, to function.

To write register data, the first three bits of the

To ensure device reset under a possible locked SPI

command byte to be shifted into the device are 011.

interface condition, do one of the following: 1) toggle

These bits are followed by the multiple register read

CS high then low and send the reset command; or 2)

bit (MUL). If MUL = '1', then multiple registers can be

hold SCLK inactive for 256/fCLK or 4096/fCLK and send

written in sequence beyond the desired register. If

the reset command. The control commands are

MUL = '0', only data to the addressed register can be

illustrated in Figure 61.

written. The remaining four bits of the command word

are the beginning register address bits. During this

time, the invalid data may appear on DOUT until the

command is completed. This data should be ignored.

Figure 60. Register Write Operation

Figure 61. Control Command Operation

Submit Documentation Feedback

Product Folder Link(s): ADS1258-EP

ADS1258IPHPREP 데이터시트(PDF) 35 Page - Texas Instruments

ADS1258IPHPREP 데이터시트(HTML) 35 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

데이터시트 다운로드

링크 URL