82801BA datasheet(45/498 Pages) INTEL

45 / 498 page

82801BA ICH2 and 82801BAM ICH2-M Datasheet

2-9

Signal Description

2.11

Processor Interface

Table 2-11. Processor Interface Signals

Name

Type

Description

A20M#

Mask A20: A20M# goes active based on setting the appropriate bit in the Port 92h

Speed Strap: During the reset sequence, ICH2 drives A20M# high if the

corresponding bit is set in the FREQ_STRP register.

CPUSLP#

Processor Sleep: This signal puts the processor into a state that saves

substantial power compared to Stop-Grant state. However, during that time, no

snoops occur. The ICH2 can optionally assert the CPUSLP# signal when going to

the S1 state.

FERR#

Numeric Coprocessor Error: This signal is tied to the coprocessor error signal

on the processor. FERR# is only used if the ICH2 coprocessor error reporting

function is enabled in the General Control Register (Device 31:Function 0, Offset

D0, bit 13). If FERR# is asserted, the ICH2 generates an internal IRQ13 to its

interrupt controller unit. It is also used to gate the IGNNE# signal to ensure that

IGNNE# is not asserted to the processor unless FERR# is active. FERR# requires

an external weak pull-up to ensure a high level when the coprocessor error

function is disabled.

IGNNE#

Ignore Numeric Error: This signal is connected to the ignore error pin on the

processor. IGNNE# is only used if the ICH2 coprocessor error reporting function is

enabled in the General Control Register (Device 31:Function 0, Offset D0,

bit 13). If FERR# is active, indicating a coprocessor error, a write to the

Coprocessor Error Register (F0h) causes the IGNNE# to be asserted. IGNNE#

remains asserted until FERR# is negated. If FERR# is not asserted when the

Coprocessor Error Register is written, the IGNNE# signal is not asserted.

Speed Strap: During the reset sequence, ICH2 drives IGNNE# high if the

corresponding bit is set in the FREQ_STRP register.

INIT#

Initialization: INIT# is asserted by the ICH2 for 16 PCI clocks to reset the

processor. ICH2 can be configured to support processor BIST. In that case, INIT#

will be active when PCIRST# is active.

INTR

Processor Interrupt: INTR is asserted by the ICH2 to signal the processor that

an interrupt request is pending and needs to be serviced. It is an asynchronous

output and normally driven low.

Speed Strap: During the reset sequence, ICH2 drives INTR high if the

corresponding bit is set in the FREQ_STRP register.

NMI

Non-Maskable Interrupt: NMI is used to force a non-maskable interrupt to the

processor. The ICH2 can generate an NMI when either SERR# or IOCHK# is

asserted. The processor detects an NMI when it detects a rising edge on NMI.

NMI is reset by setting the corresponding NMI source enable/disable bit in the NMI

Status and Control Register.

Speed Strap: During the reset sequence, ICH2 drives NMI high if the

corresponding bit is set in the FREQ_STRP register.

SMI#

System Management Interrupt: SMI# is an active low output synchronous to

PCICLK. It is asserted by the ICH2 in response to one of many enabled hardware

or software events.

STPCLK#

Stop Clock Request: STPCLK# is an active low output synchronous to PCICLK.

It is asserted by the ICH2 in response to one of many hardware or software

events. When the processor samples STPCLK# asserted, it responds by stopping

its internal clock.

82801BA 데이터시트(PDF) 45 Page - Intel Corporation

82801BA 데이터시트(HTML) 45 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL