전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

EV8680 데이터시트(PDF) 33 Page - CML Microcircuits

부품명 EV8680
상세설명  Evaluation Kit
PDF  39 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  CMLMICRO [CML Microcircuits]
홈페이지  http://www.cmlmicro.com
Logo CMLMICRO - CML Microcircuits

EV8680 데이터시트(HTML) 33 Page - CML Microcircuits

Back Button EV8680 Datasheet HTML 29Page - CML Microcircuits EV8680 Datasheet HTML 30Page - CML Microcircuits EV8680 Datasheet HTML 31Page - CML Microcircuits EV8680 Datasheet HTML 32Page - CML Microcircuits EV8680 Datasheet HTML 33Page - CML Microcircuits EV8680 Datasheet HTML 34Page - CML Microcircuits EV8680 Datasheet HTML 35Page - CML Microcircuits EV8680 Datasheet HTML 36Page - CML Microcircuits EV8680 Datasheet HTML 37Page - CML Microcircuits Next Button
Zoom Inzoom in Zoom Outzoom out
 33 / 39 page
background image
Evaluation Kit for CMX868
EV8680
© 2000 Consumer Microcircuits Limited
33
UM8680/2
1.6.8
BER Measurement
To allow the user to perform a Bit Error Rate Test (BERT) on the CMX868, the EF8680 firmware
contains a BERT routine. This facility is enabled using the test functions AT@F4 (Rx End) or AT@F5
(Tx End). Before selecting these functions the user must select the required protocol via the ATBn
command. Various bit mapped S-registers must also be modified to select the CMX868 configuration
used during the BERT.
The BERT routines have been designed for use with two EV8680 kits and a BER Datatester unit
(compatible with the EV8680 BER test pin timings, see below). The firmware only allows the user to set
up a single EV8680 board as the Tx or Rx end. The second EV8680 evaluation board(not supplied)
could be replaced with an alternative system (designed for use with the BER Datatester unit).
The EV8680 BERT is performed in synchronous mode and uses simple negotiation before data is
clocked in and out of the BER Datatester unit.
Hardware Setup
This function enables connection to BER Testers as follows:
TEST3 (J3 Pin 10) from BER Tester Tx Data O/P
TEST2 (J3 Pin 9) to BER Tester Tx Data Clock I/P
TEST1 (J3 Pin 8) to BER Tester Rx Data I/P
TEST0 (J3 Pin 7) to BER Tester Rx Data Clock I/P
The tester must be able to operate from an external clock. The timings of the clock provided from the
Evaluation board µC are as follows:
1
0
1
0
0
1
1
0
8-Bit Time
t
A
Rx Data
Clock O/P
Rx Data
O/P
Figure 5 Evaluation Board µC Rx Timing
The µC modifies the state of the Rx data output before taking the Rx clock pin high. Therefore, Rx data
is assumed to be clocked into the BER Datatester on the rising edge of Rx clock.
1
0
1
0
0
1
1
0
8-Bit Time
t
A
Tx Data
Clock O/P
Tx Data
I/P
Figure 6 Evaluation Board µC Tx Timing



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com