| 전자부품 데이터시트 검색엔진 |
|
33781 데이터시트(PDF) 16 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
33781 데이터시트(HTML) 16 Page - Freescale Semiconductor, Inc |
|
16 / 44 page ![]() Analog Integrated Circuit Device Data 16 Freescale Semiconductor 33781 FUNCTIONAL DESCRIPTIONS FUNCTIONAL PIN DESCRIPTIONS LOW SIDE BUS (DnL) There are four independent low side outputs, D0L, D1L, D2L and D3L. They comprise the low side differential output signal of the DBUS physical layer as shown in Figure 5. They also provide power to the slave modules during the DBUS idle time. The output of DnL should have a bypass capacitor of 2.2nF to ground. HIGH SIDE BUS (DnH) There are four independent high side outputs, D0H, D1H, D2H, and D3H. They comprise the high side differential output signal of the DBUS physical layer. They also provide power to the slave modules during the DBUS idle time. See Figure 5. The output of DnH should have a bypass capacitor of 2.2nF to ground. POSITIVE SUPPLY FOR BUS OUTPUT (VSUPn) This 9.0V to 25V power supply is used to provide power to the slave devices attached to the DBUS. During the bus idle time, the storage capacitors in the slave modules are charged up to maintain a regulated supply to the slave device. VSUP1 powers devices DBUS0 and DBUS1, and VSUP2 powers devices on DBUS2 and DBUS3. See Figure 9. The two supplies are interdependent internally, however, as can be seen in Figure 9: VSUP1 is used to create the VCM_REF voltage for all four driver buffers, and VSUP2 is used to supply the charge pump voltage. Consequently, both VSUP1 and VSUP2 are required for internal functions: for example, the internal voltage regulator VREG_8V is supplied from VSUP1, but uses the VSUP2-derived charge pump voltage to supply the output NMOS devices. PSEUDO BUS (DPH AND DPL) These bus high and bus low pins are created by closing the pseudo bus switches attached to the D0H and D0L bus lines internal to the 33781. This allows a second external set of bus lines to communicate over the D0 Channel. The pseudo bus switches are controlled by the system MCU through SPI0. Figure 9. VSUP Block Diagram VSUP Voltage Monitor VMID Reference for common mode voltage VREG_8V Voltage Regulator VCharge_pump DBUS 0 Driver/ Receiver DBUS 3 Driver/ Receiver DBUS 1 DBUS 2 RNE control for ch0, ch1, ch2 and ch3 status register VCP VCP V_8V VCM_REF VSUP2 (21) GND (18) VSUP1 (27) GND (32) D0H/L D1H/L GND (24) D2H/L D3H/L |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |