MCP4726 datasheet(13/86 Pages) MICROCHIP

13 / 86 page

DS22272A-page 13

MCP4706/4716/4726

111

TSP

Input filter spike

suppression

(SDA and SCL)

100 kHz mode

—

NXP Spec states N.A.

400 kHz mode

—

1.7 MHz mode

—

Spike suppression

3.4 MHz mode

—

Spike suppression

—

Standard Mode,

(Not Applicable)

50 (typ)

—

Fast Mode

10 (typ)

—

High Speed Mode 1.7

10 (typ)

—

High Speed Mode 3.4

TABLE 1-3:

I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)

I2C AC Characteristics

Standard Operating Conditions (unless otherwise specified)

Operating Temperature

–40

°C ≤ TA ≤ +125°C (Extended)

Operating Voltage VDD range is described in Electrical characteristics

Param.

No.

Sym

Characteristic

Min

Max

Units

Conditions

Note 1:

As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region

(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.

A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the

requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not

stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,

it must output the next data bit to the SDA line.

TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I

2C bus specification) before

the SCL line is released.

The MCP47X6 device must provide a data hold time to bridge the undefined part between VIH and VIL of

the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested

in order to ensure that the output data will meet the setup and hold specifications for the receiving device.

Use Cb in pF for the calculations.

Not Tested. This parameter ensured by characterization.

A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do

not unintentionally create a Start or Stop condition.

If this parameter is too short, it can create an unintentional Start or Stop condition to other devices on the

I2C bus line. If this parameter is too long, the Data Input Setup (TSU:DAT) or Clock Low time (TLOW) can be

affected.

Data Input: This parameter must be longer than tSP.

Data Output: This parameter is characterized, and tested indirectly by testing TAA parameter.

Ensured by the TAA 3.4 MHz specification test.

The specification is not part of the I

C specification. TAA = THD:DAT + TFSDA (or TRSDA).

MCP4726 데이터시트(PDF) 13 Page - Microchip Technology

MCP4726 데이터시트(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

데이터시트 다운로드

링크 URL