| 전자부품 데이터시트 검색엔진 |
|
CY29940AXCT 데이터시트(PDF) 3 Page - Cypress Semiconductor |
|
|
|||||||||||||||||||||||||||||
CY29940AXCT 데이터시트(HTML) 3 Page - Cypress Semiconductor |
|
3 / 10 page ![]() CY29940 Document #: 38-07283 Rev. *E Page 3 of 10 Maximum Ratings[2] Maximum Input Voltage Relative to VSS............. VSS – 0.3 V Maximum Input Voltage Relative to VDD............. VDD + 0.3 V Storage Temperature ................................ –65 C to +150 C Operating Temperature............................... –40 C to +85 C Maximum ESD Protection .............................................. 2 kV Maximum Power Supply................................................ 5.5 V Maximum Input Current ............................................. ±20 mA This device contains circuitry to protect the inputs against damage due to high static voltages or electric field; however, precautions should be taken to avoid application of any voltage higher than the maximum rated voltages to this circuit. For proper operation, Vin and Vout should be constrained to the range: VSS < (Vin or Vout) < VDD Unused inputs must always be tied to an appropriate logic voltage level (either VSS or VDD). DC Parameters[2] VDD = 3.3 V ± 5% or 2.5 V ± 5%, VDDC = 3.3 V ± 5% or 2.5 V ± 5%, TA = –40 C to +85 C Parameter Description Conditions Min Typ Max Unit VIL Input Low Voltage VSS –0.8 V VIH Input High Voltage 2.0 – VDD V IIL Input Low Current[3] – – –200 µA IIH Input High Current[3] –– 200 µA VPP Peak-to-Peak Input Voltage PECL_CLK 500 – 1000 mV VCMR Common Mode Range[4] PECL_CLK VDD = 3.3 V VDD – 1.4 – VDD – 0.6 V VDD = 2.5 V VDD – 1.0 – VDD – 0.6 V VOL Output Low Voltage[5, 6, 7] IOL = 20 mA – – 0.5 V VOH Output High Voltage[5, 6, 7] IOH = –20 mA, VDDC = 3.3 V 2.4 – – V IOH = –20 mA, VDDC = 2.5 V 1.8 – – V IDDQ Quiescent Supply Current – 5 7 mA IDD Dynamic Supply Current VDD = 3.3 V, Outputs @ 150 MHz, CL = 15 pF – 285 – mA VDD = 3.3 V, Outputs @ 200 MHz, CL = 15 pF – 335 – VDD = 2.5 V, Outputs @ 150 MHz, CL = 15 pF – 200 – VDD = 2.5 V, Outputs @ 200 MHz, CL = 15 pF – 240 – Zout Output Impedance VDD = 3.3 V 8 12 16 VDD = 2.5 V 10 15 20 Cin Input Capacitance – 4 – pF Notes 2. Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is not required. 3. Inputs have pull-up/pull-down resistors that effect input current. 4. The VCMR is the difference from the most positive side of the differential input signal. Normal operation is obtained when the “High” input is within the VCMR range and the input lies within the VPP specification. Driving series or parallel terminated 50 (or 50 to VDD/2) transmission lines 5. Outputs driving 50 transmission lines. 6. See Figure 1 on page 5 and Figure 2 on page 5. 7. 50% input duty cycle. [+] Feedback |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |