ADP7102ARDZ-5.0-R7 datasheet(4/28 Pages) AD

4 / 28 page

ADP7102

Data Sheet

Rev. A | Page 4 of 28

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

PROGRAMMABLE EN/UVLO

UVLO Threshold rising

UVLORISE

3.3 V ≤ VIN ≤ 20 V, TJ = −40°C to +125°C

1.18

1.23

1.28

UVLO Threshold falling

UVLOFALL

3.3 V ≤ VIN ≤ 20 V, TJ = −40°C to +125°C, 10 kΩ

in series with enable pin

1.13

UVLO Hysteresis Current

UVLOHYS

VEN > 1.25 V, TJ = −40°C to +125°C

7.5

9.8

µA

Enable Pulldown Current

IEN-IN

EN = VIN

500

INPUT VOLTAGE

Start Threshold

VSTART

TJ = −40°C to +125°C

3.2

Shutdown Threshold

VSHUTDOWN

TJ = −40°C to +125°C

2.45

Hysteresis

250

OUTPUT NOISE

OUTNOISE

10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.8 V

µV rms

10 Hz to 100 kHz, VIN = 6.3 V, VOUT = 3.3 V

µV rms

10 Hz to 100 kHz, VIN = 8 V, VOUT = 5 V

µV rms

10 Hz to 100 kHz, VIN = 12 V, VOUT = 9 V

µV rms

10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.5 V,

adjustable mode

µV rms

10 Hz to 100 kHz, VIN = 12 V, VOUT = 5 V,

adjustable mode

µV rms

10 Hz to 100 kHz, VIN = 18 V, VOUT = 15 V,

adjustable mode

µV rms

POWER SUPPLY REJECTION RATIO

PSRR

100 kHz, VIN = 4.3 V, VOUT = 3.3 V

100 kHz, VIN = 6 V, VOUT = 5 V

10 kHz, VIN = 4.3 V, VOUT = 3.3 V

10 kHz, VIN = 6 V, VOUT = 5 V

100 kHz, VIN = 3.3 V, VOUT = 1.8 V, adjustable mode

100 kHz, VIN = 6 V, VOUT = 5 V, adjustable mode

100 kHz, VIN = 16 V, VOUT = 15 V, adjustable mode

10 kHz, VIN = 3.3 V, VOUT = 1.8 V, adjustable mode

10 kHz, VIN = 6 V, VOUT = 5 V, adjustable mode

10 kHz, VIN = 16 V, VOUT = 15 V, adjustable mode

Based on an end-point calculation using 1 mA and 300 mA loads. See Figure 6 for typical load regulation performance for loads less than 1 mA.

Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output

voltages above 3.0 V.

Start-up time is defined as the time between the rising edge of EN to VOUT being at 90% of its nominal value.

Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 5.0 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 5.0 V, or 4.5 V.

INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS

Table 2.

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

Minimum Input and Output Capacitance1

CMIN

TA = −40°C to +125°C

0.7

µF

Capacitor ESR

RESR

TA = −40°C to +125°C

0.001

0.2

The minimum input and output capacitance should be greater than 0.7 μF over the full range of operating conditions. The full range of operating conditions in the

application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;

Y5V and Z5U capacitors are not recommended for use with any LDO.

ADP7102ARDZ-5.0-R7 데이터시트(PDF) 4 Page - Analog Devices

ADP7102ARDZ-5.0-R7 데이터시트(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

데이터시트 다운로드

링크 URL