SP574B datasheet(8/15 Pages) SIPEX

8 / 15 page

SP574B/674B/1674B/774B

12–Bit Sampling A/D Converters

+9.9927V for the

±10V range. Adjust the gain

potentiometer R

2 for flicker between codes 1111

1110 and 1111 1111 1111.

Alternative

The 100

Ω potentiometer R

2 provides gain adjust

for 10V and 20V ranges. In some applications, a

full scale of 10.24V (for and LSB of 2.5mV) or

20.48 (for an LSB of 5.0mV) is more convenient.

For these, replace R

2 by a 50Ω, 1% metal film

resistor. Then to provide gain adjust for the 10.24

range, add a 200

Ωpotentiometer in series with pin

13. For the 20.48V range, add a 1000

Ωpotentiom-

eter in series with pin 14.

The gain adjustment should be done at positive full

scale. The ideal input corresponding to the last

code change is applied. This is 11⁄

2LSB below the

nominal full scale which is +9.9963V for the 10V

range and +19.9927V for the 20V range. Adjust

the gain potentiometer R

2 for flicker between

codes 1111 1111 1110 and 1111 1111 1111. If

calibration is not necessary for the intended appli-

cation, replace R

2 with a 50Ω, 1% metal film

resistor and remove the network analog input to

pin 13 for the 0V to 10V range or to pin 14 for the

0V to 20V range.

Bipolar

The gain and offset errors listed in the specifica-

tions may be adjusted to zero using the potentiom-

eters R

1 and R2 (See Figure 3). If adjustment is not

needed, either or both pots may be replaced by a

Ω, 1% metal film resistor.

To calibrate, connect the analog input signal to pin

13 for a

±5V range or to pin 14 for a ±10V range.

First apply a DC input voltage 1⁄

2 LSB above

negative full scale which is –4.9988V for the

±5V

range or –9.9976V for the

±10V range. Adjust the

offset potentiometer R

1 for flicker between output

codes 0000 0000 0000 and 0000 0000 0001. Next,

apply a DC input voltage 11⁄

2 LSB below positive

full scale which is +4.9963V for the

±5 range or

CONTROLLING THE SPx74B

The SPx74B can be operated by most micropro-

cessor systems due to the control input pins and

on–chip logic. It may also be operated in the

“stand–alone” mode and enabled by the R/C

input pin. Full microprocessor control consists

of selecting an 8– or 12–bit conversion cycle,

initiating the conversion, and reading the output

data when ready. The output read has the options

of choosing either 12–bits at once or 8–bits fol-

lowed by 4–bits in a left–justified format. All five

control inputs are TTL/CMOS compatible and

include 12/8, CS, A

0, R/C and CE. The use of these

inputs in controlling the converter’s operation is

Figure 3. Bipolar Input Connections

STS

12/8

R/C

THREE–STATE BUFFERS AND CONTROL

NIBBLE A

NIBBLE B

NIBBLE C

21 20

19 18

17 16

OUTPUT BITS

MSB

LSB

CONTROL

LOGIC

OSCILLATOR

12–BITS

SAMPLE/HOLD

CDAC

LSB

MSB

OFFSET/GAIN

TRIM NETWORK

REF

AMP

VREF

OUT

VREF

100

Ω

10V

20V

BIP

OFF

ANALOG

INPUTS

12–BIT SAR

COMP

STROBE

100

Ω

±5V

±10V

DGND

VLOGIC

+5V

711

VCC

VEE

AGND

+15V

N.C.

10µF

0.1µF

10µF

0.1µF

SP574B 데이터시트(PDF) 8 Page - Sipex Corporation

SP574B 데이터시트(HTML) 8 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

데이터시트 다운로드

링크 URL