MCM69P735

8

MOTOROLA FAST SRAM

AC OPERATING CONDITIONS AND CHARACTERISTICS

(3.6 V

≥ VDD ≥ 3.135 V, 70°C ≥ TA ≥ 0°C, Unless Otherwise Noted)

Input Timing Measurement Reference Level

1.5 V

. . . . . . . . . . . . . . .

Input Pulse Levels

0 to 3.0 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input Slew Rate (See Note 1)

1.0 V/ns

. . . . . . . . . . . . . . . . . . . . . . . . .

Output Timing Reference Level

1.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . .

Output Load

See Figure 2 Unless Otherwise Noted

. . . . . . . . . . . . . .

Output Rise/Fall Times (Max)

2.0 ns

. . . . . . . . . . . . . . . . . . . . . . . . . . .

P

Sb l

MCM69P735–2.5

200 MHz

MCM69P735–3

180 MHz

MCM69P735–3.5

166 MHz

Ui

N

Parameter

Symbol

Min

Max

Min

Max

Min

Max

Unit

Notes

Cycle Time

tKHKH

5

—

5.5

—

6

—

ns

Clock High Pulse Width

tKHKL

2.2

—

2.5

—

2.7

—

ns

3, 4

Clock Low Pulse Width

tKLKH

2.2

—

2.5

—

2.7

—

ns

3, 4

Clock Access Time

tKHQV

—

2.5

—

3.0

—

3.5

ns

3

Output Enable to Output Valid

tGLQV

—

3.5

—

3.5

—

3.8

ns

3

Clock High to Output Active

tKHQX1

0

—

0

—

0

—

ns

3, 5, 6

Clock High to Output Change

tKHQX2

1.5

—

1.5

—

1.5

—

ns

3, 6

Output Enable to Output Active

tGLQX

0

—

0

—

0

—

ns

3, 5, 6

Output Disable to Q High–Z

tGHQZ

—

3.5

—

3.5

—

3.8

ns

3, 5, 6

Clock High to Q High–Z

tKHQZ

1.5

5

1.5

5.5

1.5

6

ns

3, 5, 6

Setup Times:

Address

Data In

Write

Chip Enable

ADSP, ADSC, ADV

tADKH

tDVKH

tWVKH

tEVKH

tADSKH

0.5

0.5

0.5

0.5

1.5

—

0.5

0.5

0.5

0.5

1.5

—

0.5

0.5

0.5

0.5

1.5

—

ns

3

Hold Times:

Address

ADSP, ADSC, ADV

Data In

Write

Chip Enable

tKHAX

tKHADSX

tKHDX

tKHWX

tKHEX

1.0

—

1.0

—

1.0

—

ns

3

NOTES:

1. Write is defined as either any SBx and SW low or SGW is low. Chip Enable is defined as SE1 low, SE2 high and SE3 low whenever ADSP

or ADSC is asserted.

2. All read and write cycle timings are referenced from K or G.

3. Tested per AC Test Load, Figure 2.

4. In order to reduce test correlation issues and to reduce the effects of application specific input edge rate variations on correlation between

data sheet parameters and actual system performance, FSRAM AC parametric specifications are always specified at VDDQ/2. In some

design exercises, it is desirable to evaluate timing using other reference levels. Since the maximum test input edge rate is known and is given

in the AC Test Conditions section of the data sheet as 1 V/ns, one can easily interpolate timing values to other reference levels.

5. Measured at

6. This parameter is sampled and not 100% tested.