______________________________________________________________________________________

13

Package Information

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

0.10 C

0.08 C

0.10 M C A B

D

D/2

E/2

E

A1

A2

A

E2

E2/2

L

k

e

(ND - 1) X e

(NE - 1) X e

D2

D2/2

b

L

e

L

C

L

e

C

L

L

C

L

C

PACKAGE OUTLINE

21-0136

2

1

I

8, 12, 16L THIN QFN, 3x3x0.8mm

MARKING

AAAA

EXPOSED PAD VARIATIONS

CODES

PKG.

T1233-1

MIN.

0.95

NOM.

1.10

D2

NOM.

1.10

MAX.

1.25

MIN.

0.95

MAX.

1.25

E2

12

N

k

A2

0.25

NE

A1

ND

0

0.20 REF

-

-

3

0.02

3

0.05

L

e

E

0.45

2.90

b

D

A

0.20

2.90

0.70

0.50 BSC.

0.55

3.00

0.65

3.10

0.25

3.00

0.75

0.30

3.10

0.80

16

0.20 REF

0.25

-

0

4

0.02

4

-

0.05

0.50 BSC.

0.30

2.90

0.40

3.00

0.20

2.90

0.70

0.25

3.00

0.75

3.10

0.50

0.80

3.10

0.30

PKG

REF.

MIN.

12L 3x3

NOM. MAX.

NOM.

16L 3x3

MIN.

MAX.

0.35 x 45

°

PIN ID

JEDEC

WEED-1

T1233-3

1.10

1.25

0.95

1.10

0.35 x 45

°

1.25

WEED-1

0.95

T1633F-3

0.65

T1633-4

0.95

0.80

0.95

0.65

0.80

1.10

1.25

0.95

1.10

0.225 x 45

°

0.95

WEED-2

0.35 x 45

°

1.25

WEED-2

T1633-2

0.95

1.10

1.25

0.95

1.10

0.35 x 45

°

1.25

WEED-2

PACKAGE OUTLINE

21-0136

2

2

I

8, 12, 16L THIN QFN, 3x3x0.8mm

WEED-1

1.25

1.10

0.95

0.35 x 45

°

1.25

1.10

0.95

T1233-4

T1633FH-3

0.65

0.80

0.95

0.225 x 45

°

0.65

0.80

0.95

WEED-2

NOTES:

1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.

2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.

3. N IS THE TOTAL NUMBER OF TERMINALS.

4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO

JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED

WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR

MARKED FEATURE.

5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm

FROM TERMINAL TIP.

6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.

7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.

8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS

.

9. DRAWING CONFORMS TO JEDEC MO220 REVISION C.

10. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.

11. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.

12. WARPAGE NOT TO EXCEED 0.10mm.

0.25

0.30

0.35

2

0.25

0

0.20 REF

-

-

0.02

0.05

0.35

8

2

0.55

0.75

2.90

2.90

3.00

3.10

0.65 BSC.

3.00

3.10

8L 3x3

MIN.

0.70

0.75

0.80

NOM. MAX.

TQ833-1

1.25

0.25

0.70

0.35 x 45

°

WEEC

1.25

0.70

0.25

T1633-5

0.95

1.10

1.25

0.35 x 45

°

WEED-2

0.95

1.10

1.25