| 전자부품 데이터시트 검색엔진 |
|
CDH2D09 데이터시트(PDF) 12 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
CDH2D09 데이터시트(HTML) 12 Page - Maxim Integrated Products |
|
12 / 44 page ![]() PMIC with Integrated Charger and Smart Power Selector for Handheld Devices 12 ______________________________________________________________________________________ Note 2: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed through cor- relation using statistical quality control (SQC) methods. Note 3: The USB/DC current limit does not include the VL output current. See the VL Linear Regulator section for more information. Note 4: Quiescent current excludes the energy needed for the REG1–REG5 external resistor-dividers. All typical operating charac- teristics include the energy for the REG1–REG5 external resistor-dividers. For the circuit of Figure 1, the typical quiescent current with DC and USB unconnected, EN = high, VBAT = 4V, and PWM = low is 175µA. Note 5: The charger transitions from done to fast-charge mode at this BAT recharge threshold (Figure 7). Note 6: The charger transitions from fast-charge to top-off mode at this top-off threshold (Figure 7). Note 7: The maximum output current is guaranteed by correlation to the p-channel current-limit threshold, p-channel on-resistance, n-channel on-resistance, oscillator frequency, input voltage range, and output voltage range. The parameter is stated for a 4.7µH inductor with 0.13 Ω series resistance. See the Step-Down Converter Output Current section for more information. Note 8: The step-down output voltages are 1% high with no load due to the load-line architecture. When calculating the external resistor-dividers, use an FB_ voltage of 1.000V. Note 9: Line regulation for the step-down converters is measured as ΔVOUT/ΔD, where D is the duty cycle (approximately VOUT/VIN). Note 10: The skip mode current threshold is the transition point between fixed-frequency PWM operation and skip mode operation. The specification is given in terms of output load current for inductor values shown in the typical application circuits. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS BVSET Input-Voltage High VUSB or VDC = 4.1V to 6.6V VVL - 0.3 VVL + 0.3 V Internal BVSET Pullup Resistance 52.5 k Ω External BVSET Pulldown Resistance for Midrange Voltage RBVSET 45 50 55 k Ω ELECTRICAL CHARACTERISTICS (continued) (DC, USB, BVSET, UOK, DOK, LX_ unconnected; VTHM = VL/2, VPG_ = VAGND = 0V, VBAT = 4V, CEN = low, USUS = low, EN = high, VPEN1 = VPEN2 = 3.3V, VPWM = 0V, COUT4 = 1µF, COUT5 = 1µF, CSYS = 10µF, PV1 = PV2 = PV3 = PV4 = PV5 = SYS, RDISET = 3kΩ, RCISET = 3kΩ, CVL = 0.1µF, CCT = 0.15µF, CBP = 0.01µF, VFB1 = 1.1V, VFB2 = 1.1V, VFB3 = 1.1V, TA = -40°C to +85°C, unless other- wise noted.) (Note 2) |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |