전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AD1885 데이터시트(PDF) 26 Page - Analog Devices

부품명 AD1885
상세설명  AC??7 SoundMAX Codec
PDF  27 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  AD [Analog Devices]
홈페이지  http://www.analog.com
Logo AD - Analog Devices

AD1885 데이터시트(HTML) 26 Page - Analog Devices

Back Button AD1885 Datasheet HTML 19Page - Analog Devices AD1885 Datasheet HTML 20Page - Analog Devices AD1885 Datasheet HTML 21Page - Analog Devices AD1885 Datasheet HTML 22Page - Analog Devices AD1885 Datasheet HTML 23Page - Analog Devices AD1885 Datasheet HTML 24Page - Analog Devices AD1885 Datasheet HTML 25Page - Analog Devices AD1885 Datasheet HTML 26Page - Analog Devices AD1885 Datasheet HTML 27Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 26 / 27 page
background image
AD1885
–26–
REV. 0
PC_BEEP INPUT CONNECTIONS
The recommended PC_BEEP input circuit is shown below. Under most cases the PC_BEEP signal should be attenuated, filtered and
then ac-coupled into the Codec.
TO CODEC PC_BEEP INPUT
PC_BEEP (FROM ICH)
Figure 17. Recommended PC_BEEP Connections
GROUNDING AND LAYOUT
To reduce noise and emissions, Analog Devices recommends a split ground plane as shown in Figure 18. The purpose of splitting
the ground plane is to create a low noise analog area that is somewhat isolated from the digital ground current noise generated
by the system’s logic. All the analog circuitry should be placed on the analog ground plane area.
For reference purposes, and to return power supply currents, the analog and digital ground planes must be connected at some point,
ideally a small bridge under or near the Codec should be provided. A 0
Ω resistor or a ferrite bead should also be considered since
these allow some flexibility in optimizing the layout to meet EMC requirements.
PIN 1
ISOLATION
TRENCH
CONNECT SPLIT GROUND
PLANES AT OR NEAR CODEC.
ANALOG
GROUND PLANE
DIGITAL
GROUND PLANE
AD1885
Figure 18. Recommended Split Ground Plane
ANALOG POWER SUPPLY
To minimize audio noise, the Codec analog power supply (AVDD) should be well decoupled and regulated. In PC systems it is rec-
ommended that the analog supply be derived from the 12 V PC power supply using a localized linear voltage regulator. Preferably,
the analog power supply should be connected to the Codec’s analog section using a ferrite bead.
If a power plane layer is being used in the system design, it is recommended that the analog power plane for the Codec also be split
(mirroring the analog ground plane). In this case, the analog power supply ferrite bead should bridge the isolation trench, close to
the Codec location.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com