AD22050R datasheet(2/8 Pages) AD

2 / 8 page

ORDERING GUIDE

Model

Temperature Range

Package Descriptions

Package Options

AD22050N

–40

°C to +125°C

Plastic DIP

N-8

AD22050R

–40

°C to +125°C

Plastic SOIC

SO-8

AD22050R-Reel

–40

°C to +125°C

Tape and Reel

SO-8*

*Quantities must be in increments of 2,500 pieces each.

AD22050–SPECIFICATIONS

REV. C

–2–

(TA = +25 C, VS = +5 V, and VCM = 0, RL = 10 k

unless otherwise noted)

Parameter

Test Conditions

Min

Typ

Max

Units

INPUTS (Pins 1 and 8)

+CMR

Positive Common-Mode Range

TA = TMIN to TMAX

+24

–CMR

Negative Common-Mode Range

TA = TMIN to +85°C

–1.0

CMRRLF

Common-Mode Rejection Ratio

≤ 10 Hz

CMRRHF

Common-Mode Rejection Ratio

f = 10 kHz

RINCM

Common-Mode Input Resistances

Pin 1 or Pin 8 to Pin 2

180

240

300

Ω

RMATCH

Matching of Resistances

±0.5

RINDIFF

Differential Input Resistance

Pin 1 to Pin 8

280

400

Ω

PREAMPLIFIER

GCL

Closed-Loop Gain1

9.7

10.0

10.3

Output Voltage Range (Pin 3)

+0.01

+4.8

Output Resistance

100

103

Ω

OUTPUT BUFFER

GCL

Closed-Loop Gain

RLOAD

≥ 10 kΩ

1.94

2.0

2.06

Output Voltage Range3

TA = TMIN to TMAX

+0.02

+4.8

Output Resistance (Pin 5)

≥ 0.1 V dc, I

O < 1 mA

2.0

Ω

OVERALL SYSTEM

Gain

≥ 0.1 V dc

19.9

20.0

20.1

Over Temperature

TA = TMIN to TMAX

19.8

20.2

VOS

Input Offset Voltage4

–1

0.03

Over Temperature

TA = TMIN to TMAX

–3

OFS

Midscale Offset (Pin 7) Scaling

0.49

0.50

0.51

V/V

Input Resistance

Pin 7 to Pin 2

2.5

3.0

Ω

IOSC

Short-Circuit Output Current

TA = TMIN to TMAX

1125mA

BW–3 dB

–3 dB Bandwidth

VO = +1 V dc

kHz

Slew Rate

0.2

µs

NSD

Noise Spectral Density3

f = 100 Hz to 10 kHz

0.2

µV/√Hz

POWER SUPPLY

Operating Range

TA = TMIN to TMAX

3.0

Quiescent Supply Current5

TA = +25

°C, V

S = +5 V

200

500

µA

TEMPERATURE RANGE

TOP

Operating Temperature Range

–40

+125

°C

NOTES

1Specified for default mode, i.e., with no external components. The overall gain is trimmed to 0.5%, while the individual gains of A1 and A2 may be subject to a

maximum

±3% tolerance. Note that the actual gain in a particular application can be modified by the use of external resistor networks.

2The actual output resistance of A1 is only a few ohms, but access to this output, via Pin 3, is always through the resistor R12 (see Figure 16) which is 100 k

Ω,

trimmed to

± 3%.

3For V

CM ≤ 20 V. For VCM > 20 V, VOL ≅ 1 mV/V × VCM.

4Referred to the input (Pins 1 and 8).

5With V

DM = 0 V. Differential mode signals are referred to as V DM, while VCM refers to common-mode voltages—see the section Product Description and Figure 3.

All min and max specifications are guaranteed, although only those marked in boldface are tested on all production units at final test.

Specifications subject to change without notice.

AD22050R 데이터시트(PDF) 2 Page - Analog Devices

AD22050R 데이터시트(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

데이터시트 다운로드

링크 URL