D4454 datasheet(2/6 Pages) AOSMD

2 / 6 page

AOD4454

Symbol

Min

Typ

Max

Units

BVDSS

150

VDS=150V, VGS=0V

TJ=55°C

IGSS

±100

VGS(th)

Gate Threshold Voltage

3.4

4.6

ID(ON)

75.5

TJ=125°C

151

188

110

Ω

gFS

VSD

0.72

Ciss

655

820

985

Coss

Crss

0.7

1.4

2.1

Ω

Qg(10V)

Qgs

Qgd

4.4

tD(on)

10.5

5.5

tD(off)

14.5

trr

32.5

Qrr

160

230

300

THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL

COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING

OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,

FUNCTIONS AND RELIABILITY WITHOUT NOTICE.

IS=1A,VGS=0V

VDS=5V, ID=10A

IF=10A, dI/dt=500A/µs

SWITCHING PARAMETERS

Maximum Body-Diode Continuous Current

Input Capacitance

Output Capacitance

Turn-On DelayTime

DYNAMIC PARAMETERS

Turn-On Rise Time

Reverse Transfer Capacitance

VGS=0V, VDS=75V, f=1MHz

Body Diode Reverse Recovery Charge IF=10A, dI/dt=500A/µs

Turn-Off DelayTime

VGS=10V, VDS=75V, ID=10A

Gate Source Charge

Gate Drain Charge

Gate resistance

VGS=0V, VDS=0V, f=1MHz

Turn-Off Fall Time

Total Gate Charge

RDS(ON)

Static Drain-Source On-Resistance

IDSS

µA

VDS=VGS ID=250µA

VDS=0V, VGS= ±20V

Zero Gate Voltage Drain Current

Gate-Body leakage current

Ω

Body Diode Reverse Recovery Time

Drain-Source Breakdown Voltage

ID=250µA, VGS=0V

VGS=10V, VDS=5V

VGS=10V, ID=10A

On state drain current

VGS=7V, ID=10A

Forward Transconductance

Diode Forward Voltage

VGS=10V, VDS=75V, RL=7.5Ω,

RGEN=3Ω

Electrical Characteristics (TJ=25°C unless otherwise noted)

STATIC PARAMETERS

Parameter

Conditions

A. The value of RθJA is measured with the device mounted on 1in

2 FR-4 board with 2oz. Copper, in a still air environment with T

A =25°C. The

Power dissipation PDSM is based on R θJA and the maximum allowed junction temperature of 150°C. The value in any given application depends

on the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allow s it.

B. The power dissipation PD is based on TJ(MAX)=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper

dissipation limit for cases where additional heatsinking is used.

C. Repetitive rating, pulse width limited by junction temperature TJ(MAX)=175°C. Ratings are based on low frequency and duty cycles to keep

initial TJ =25°C.

D. The RθJA is the sum of the thermal impedence from junction to case RθJC and case to ambient.

E. The static characteristics in Figures 1 to 6 are obtained using <300

µs pulses, duty cycle 0.5% max.

F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink,

assuming a maximum junction temperature of TJ(MAX)=175°C. The SOA curve provides a single pulse ratin g.

G. The maximum current rating is package limited.

H. These tests are performed with the device mounted on 1 in

2 FR-4 board with 2oz. Copper, in a still air environment with T

A=25°C.

Rev 0: February 2011

www.aosmd.com

Page 2 of 6

D4454 데이터시트(PDF) 2 Page - Alpha & Omega Semiconductors

D4454 데이터시트(HTML) 2 Page - Alpha & Omega Semiconductors

Html Pages

1 2 3 4 5 6

데이터시트 다운로드

링크 URL