| 전자부품 데이터시트 검색엔진 |
|
VWQBS2-SIP 데이터시트(PDF) 4 Page - CUI INC |
|
|
|||||||||||||||||||||||||||||
VWQBS2-SIP 데이터시트(HTML) 4 Page - CUI INC |
|
4 / 5 page ![]() cui.com CUI Inc │ SERIES: VWQBS2-SIP │ DESCRIPTION: DC-DC CONVERTER date 09/10/2012 │ page 4 of 5 1. Requirement on Output Load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power. 2. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. 3. Recommended Circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor see (Table 1). 4. CTRL Terminal When open or high impedance, the converter work well; When this pin is ‘high’; the converter shutdown; It should be note that the input current should between 5~10 mA,exceeding the maximum 20 mA will cause permanence damage to the converter. The value of Vc not limited and desirable 5 Vdc, 12 Vdc, or directly with Vin. The value of R can be derived as follows: 5. Input Current Nominal input voltage range. The input current of the power supply must be sufficient to the startup current (Ip) of the DC-DC module. General: Ip ≤1.4*Iin-max 6. No parallel connection or plug and play +Vo 0V Cout C1 Vin GND 2 1 6 9 3 Lin Vc R Ic C2 D1 Table 1 APPLICATION NOTES Input Voltage (V) Inp ut Voltage Ra nge Ip R= V C-VD-1.0 I C Figure 1 C1/C2 10 ~ 100 μF Lin 4.7 ~ 120 μH Cout 100 μF Vin (Vdc) Fuse (slow-blow type) (mA) 24 250 48 150 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |