AD9736BBC datasheet(39/72 Pages) AD

39 / 72 page

AD9734/AD9735/AD9736

Rev. A | Page 39 of 72

INTERPOLATION FILTER

In 2× mode, the input data is interpolated by a factor of 2 so

that it aligns with the DAC update rate. The interpolation filter

is a hard-coded, 55-tap, symmetric FIR with a 0.001 dB pass-

band flatness and a stop-band attenuation of about 90 dB. The

transition band runs from 20% of fDAC to 30% of fDAC. The FIR

response is shown in Figure 75 where the frequency axis is

normalized to fDAC. Figure 76 shows the pass-band flatness and

Table 23 shows the 16-bit filter coefficients.

Table 23. FIR Interpolation Filter Coefficients

Coefficient Number

Tap Weight

−7

+24

−62

+135

−263

+471

−793

+1273

−1976

+3012

−4603

+7321

−13270

+41505

+65535

FREQUENCY NORMALIZED TO

fDAC

0.50

0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

Figure 75. Interpolation Filter Response

FREQUENCY NORMALIZED TO

fDAC

0.25

0.10

0.05

0.15

0.20

0.10

0.06

0.08

0.02

–0.02

–0.06

0.04

–0.04

–0.08

–0.10

Figure 76. Interpolation Filter Pass-Band Flatness

DATA INTERFACE CONTROLLERS

Two internal controllers are utilized in the operation of the

AD973x. The first controller helps maintain optimum LVDS

data sampling; the second controller helps maintain optimum

synchronization between the DACCLK and the incoming data.

The LVDS controller is responsible for optimizing the sampling

of the data from the LVDS bus (DB13:0), while the sync

controller resolves timing problems between the DAC_CLK

(CLK+, CLK−) and the DATACLK. A block diagram of these

controllers is shown in Figure 77.

DATACLK_OUT

DATACLK

DATACLK_IN

FIFO

DAC

LVDS

SAMPLE

LOGIC

CLK

CONTROL

LVDS

CONTROLLER

DB<13:0>

DATA

SOURCE

i.e., FPGA

SYNC

LOGIC

SYNC

CONTROLLER

Figure 77. Data Controllers

The controllers are clocked with a divided-down version of the

DAC_CLK. The divide ratio is set utilizing the controller clock

predivider bits (CCD<3:0>) located at Reg. 22, Bits 3:0 to

generate the controller clock as follows:

Controller Clock = DAC_CLK/(2(CCD<3:0> + 4))

Note that the controller clock cannot exceed 10 MHz for correct

operation. Until CCD<3:0> is properly programmed to meet

this requirement, the DAC output may not be stable. This

means the FIFO cannot be enabled in PIN_MODE unless the

DACCLK is less than 160 MHz.

AD9736BBC 데이터시트(PDF) 39 Page - Analog Devices

AD9736BBC 데이터시트(HTML) 39 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

데이터시트 다운로드

링크 URL