OMAP3530ECBBA datasheet(234/264 Pages) TI1

234 / 264 page

6.7 Removable Media Interfaces

6.7.1

High-Speed Multimedia Memory Card (MMC) and Secure Digital IO Card (SDIO) Timing

6.7.1.1 MMC/SD/SDIO in SD Identification Mode

OMAP3530/25 Applications Processor

SPRS507F – FEBRUARY 2008 – REVISED OCTOBER 2009

www.ti.com

The MMC/SDIO host controller provides an interface to high-speed and standard MMC, SD memory

cards, or SDIO cards. The application interface is responsible for managing transaction semantics. The

MMC/SDIO host controller deals with MMC/SDIO protocol at transmission level, packing data, adding

CRC, start/end bit, and checking for syntactical correctness.

There are three MMC interfaces on the OMAP3530/25:

• MMC/SD/SDIO Interface 1:

–

1.8 V/3 V support

–

8 bits

• MMC/SD/SDIO Interface 2:

–

1.8 V support

–

8 bits

–

4 bits with external transceiver allowing to support 3 V peripherals. Transceiver direction control

signals are multiplexed with the upper four data bits.

• MMC/SD/SDIO Interface 3:

–

1.8 V support

–

8 bits

Table 6-118 and Table 6-119 assume testing over the recommended operating conditions and electrical

characteristic conditions.

Table 6-117. MMC/SD/SDIO Timing Conditions – SD Identification Mode

TIMING CONDITION PARAMETER

VALUE

UNIT

SD Identification Mode

Input Conditions

Input signal rise time

Input signal fall time

Output Conditions

CLOAD

Output load capacitance

Table 6-118. MMC/SD/SDIO Timing Requirements – SD Identification Mode(1)(2)(3)

NO.

PARAMETER

1.15 V

1.0 V

UNIT

MIN

MAX

MIN

MAX

SD Identification Mode

MMC/SD/SDIO Interface 1 (1.8 V IO)

HSSD3/SD3

tsu(CMDV-CLKIH)

Setup time, mmc1_cmd valid before

1198.4

mmc1_clk rising clock edge

HSSD4/SD4

tsu(CLKIH-CMDIV)

Hold time, mmc1_cmd valid after

1249.2

mmc1_clk rising clock edge

MMC/SD/SDIO Interface 1 (3.0 V IO)

HSSD3/SD3

tsu(CMDV-CLKIH)

Setup time, mmc1_cmd valid before

1198.4

mmc1_clk rising clock edge

HSSD4/SD4

tsu(CLKIH-CMDIV)

Hold time, mmc1_cmd valid after

1249.2

mmc1_clk rising clock edge

MMC/SD/SDIO Interface 2

(1)

Timing parameters are referred to output clock specified in Table 6-119.

(2)

The timing requirements are assured for the cycle jitter and duty cycle error conditions specified in Table 6-119.

(3)

Corresponding figures showing timing parameters are common with other interface modes. (See SD and HS SD modes).

TIMING REQUIREMENTS AND SWITCHING CHARACTERISTICS

234

Submit Documentation Feedback

OMAP3530ECBBA 데이터시트(PDF) 234 Page - Texas Instruments

OMAP3530ECBBA 데이터시트(HTML) 234 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL