MPC8315 datasheet(34/106 Pages) FREESCALE

34 / 106 page

MPC8315E PowerQUICC II Pro Processor Hardware Specifications, Rev. 2

Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

9.5

SGMII Interface Electrical Characteristics

Each SGMII port features a 4-wire AC-Coupled serial link from the dedicated SerDes interface of

MPC8315E as shown in Figure 18, where CTX is the external (on board) AC-Coupled capacitor. Each

output pin of the SerDes transmitter differential pair features 50-

output impedance. Each input of the

SerDes receiver differential pair features 50-

 on-die termination to XCOREVSS. The reference circuit

of the SerDes transmitter and receiver is shown in Figure 49.

When an eTSEC port is configured to operate in SGMII mode, the parallel interface’s output signals of

this eTSEC port can be left floating. The input signals should be terminated based on the guidelines

described in Section 26.4, “Connection Recommendations,” as long as such termination does not violate

the desired POR configuration requirement on these pins, if applicable.

When operating in SGMII mode, the TSEC_GTX_CLK125 clock is not required for this port. Instead,

SerDes reference clock is required on SD_REF_CLK and SD_REF_CLK pins.

9.5.1

DC Requirements for SGMII SD_REF_CLK and SD_REF_CLK

The characteristics and DC requirements of the separate SerDes reference clock are described in

Section 15, “High-Speed Serial Interfaces (HSSI).”

9.5.2

AC Requirements for SGMII SD_REF_CLK and SD_REF_CLK

This table lists the SGMII SerDes reference clock AC requirements. Please note that SD_REF_CLK and

SD_REF_CLK are not intended to be used with, and should not be clocked by, a spread spectrum clock

source.

9.5.3

SGMII Transmitter and Receiver DC Electrical Characteristics

Table 35 and Table 36 describe the SGMII SerDes transmitter and receiver AC-coupled DC electrical

characteristics. Transmitter DC characteristics are measured at the transmitter outputs (SD_TX[n] and

SD_TX[n]) as depicted in Figure 17.

Note:

1. The timer can operate on rtc_clock or tmr_clock. These clocks get muxed and any one of them can be selected.

2. Asynchronous signals.

3. Inputs need to be stable at least one TMR clock.

Table 34. SD_REF_CLK and SD_REF_CLK AC Requirements

Symbol

Parameter Description

Min

Typical

Max

Unit

Note

tREF

REFCLK cycle time

—

tREFCJ

REFCLK cycle-to-cycle jitter. Difference in the period of any two adjacent

REFCLK cycles

——

100

—

tREFPJ

Phase jitter. Deviation in edge location with respect to mean edge location

–50

—

Table 33. 1588 Timer AC Specifications (continued)

Parameter

Symbol

Min

Max

Unit

Note

MPC8315 데이터시트(PDF) 34 Page - Freescale Semiconductor, Inc

MPC8315 데이터시트(HTML) 34 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL