DSPIC33FJ12MC201TESS datasheet(107/304 Pages) MICROCHIP

107 / 304 page

DS70265E-page 107

dsPIC33FJ12MC201/202

OSCCON: OSCILLATOR CONTROL REGISTER(1,3)

U-0

R-0

U-0

R/W-y

—

COSC<2:0>

—

NOSC<2:0>(2)

bit 15

bit 8

R/W-0

R-0

U-0

R/C-0

U-0

R/W-0

CLKLOCK

IOLOCK

LOCK

—CF

—

LPOSCEN

OSWEN

bit 7

bit 0

Legend:

y = Value set from Configuration bits on POR

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 15

Unimplemented:

Read as ‘0’

bit 14-12

COSC<2:0>:

Current Oscillator Selection bits (read-only)

111

= Fast RC oscillator (FRC) with Divide-by-n

110

= Fast RC oscillator (FRC) with Divide-by-16

101

= Low-Power RC oscillator (LPRC)

100

= Secondary oscillator (SOSC)

011

= Primary oscillator (XT, HS, EC) with PLL

010

= Primary oscillator (XT, HS, EC)

001

= Fast RC oscillator (FRC) with Divide-by-n plus PLL

000

= Fast RC oscillator (FRC)

bit 11

Unimplemented:

Read as ‘0’

bit 10-8

NOSC<2:0>:

New Oscillator Selection bits (2)

111

= Fast RC oscillator (FRC) with Divide-by-n

110

= Fast RC oscillator (FRC) with Divide-by-16

101

= Low-Power RC oscillator (LPRC)

100

= Secondary oscillator (SOSC)

011

= Primary oscillator (XT, HS, EC) with PLL

010

= Primary oscillator (XT, HS, EC)

001

= Fast RC oscillator (FRC) with Divide-by-n plus PLL

000

= Fast RC oscillator (FRC)

bit 7

CLKLOCK:

Clock Lock Enable bit

If clock switching is enabled and FSCM is disabled, (FOSC<FCKSM> = 0b01)

= Clock switching is disabled, system clock source is locked

= Clock switching is enabled, system clock source can be modified by clock switching

bit 6

IOLOCK:

Peripheral Pin Select Lock bit

= Peripherial pin select is locked, write to peripheral pin select registers not allowed

= Peripherial pin select is not locked, write to peripheral pin select registers allowed

bit 5

LOCK:

PLL Lock Status bit (read-only)

= Indicates that PLL is in lock, or PLL start-up timer is satisfied

= Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled

bit 4

Unimplemented:

Read as ‘0’

Note 1:

Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70186) in the

“dsPIC33F/PIC24H Family Reference Manual”

(available from the Microchip web site) for details.

Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.

This applies to clock switches in either direction. In these instances, the application must switch to FRC

mode as a transition clock source between the two PLL modes.

This register is reset only on a Power-on Reset (POR).

DSPIC33FJ12MC201TESS 데이터시트(PDF) 107 Page - Microchip Technology

DSPIC33FJ12MC201TESS 데이터시트(HTML) 107 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL