LMP7701MFX datasheet(5/35 Pages) TI

5 / 35 page

LMP7701, LMP7702, LMP7704

www.ti.com

SNOSAI9H – SEPTEMBER 2005 – REVISED MARCH 2013

5V Electrical Characteristics

(1)

Unless otherwise specified, all limits are ensured for TA = 25°C, V

+ = 5V, V− = 0V, V

CM = V

+/2, and R

L > 10 kΩ to V

+/2.

Boldface limits apply at the temperature extremes.

Parameter

Test Conditions

Min (2)

Typ (3)

Max (2)

Units

VOS

Input Offset Voltage

LMP7701

±37

±200

±500

μV

LMP7702/LMP7704

±32

±220

±520

TCVOS

Input Offset Voltage Temperature Drift

(4)

±1

±5

μV/°C

Input Bias Current

(4) (5)

±0.2

±1

−40°C ≤ TA ≤ 85°C

±50

(4) (5)

±0.2

±1

−40°C ≤ TA ≤ 125°C

±400

IOS

Input Offset Current

CMRR

Common Mode Rejection Ratio

≤ VCM ≤ 5V

130

LMP7701

≤ VCM ≤ 5V

130

LMP7702/LMP7704

PSRR

Power Supply Rejection Ratio

2.7V

≤ V+ ≤ 12V, VO = V

+/2

100

CMVR

Common Mode Voltage Range

CMRR

≥ 80 dB

–0.2

5.2

CMRR

≥ 78 dB

–0.2

5.2

AVOL

Open Loop Voltage Gain

RL = 2 kΩ (LMP7701)

100

119

VO = 0.3V to 4.7V

RL = 2 kΩ (LMP7702/LMP7704)

100

119

VO = 0.3V to 4.7V

RL = 10 kΩ

100

130

VO = 0.2V to 4.8V

VOUT

Output Voltage Swing High

RL = 2 kΩ to V

+/2

110

LMP7701

130

RL = 2 kΩ to V

+/2

120

LMP7702/LMP7704

200

from V+

RL = 10 kΩ to V

+/2

LMP7701

RL = 10 kΩ to V

+/2

LMP7702/LMP7704

120

Output Voltage Swing Low

RL = 2 kΩ to V

+/2

LMP7701

RL = 2 kΩ to V

+/2

120

LMP7702/LMP7704

190

RL = 10 kΩ to V

+/2

LMP7701

RL = 10 kΩ to V

+/2

LMP7702/LMP7704

100

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under

conditions of internal self-heating where TJ > TA.

(2)

Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using the

Statistical Quality Control (SQC) method.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(4)

This parameter is specified by design and/or characterization and is not tested in production.

(5)

Positive current corresponds to current flowing into the device.

Submit Documentation Feedback

Product Folder Links: LMP7701 LMP7702 LMP7704

LMP7701MFX 데이터시트(PDF) 5 Page - Texas Instruments

LMP7701MFX 데이터시트(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

데이터시트 다운로드

링크 URL