 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
GRM552B11H102KA01D 데이터시트(PDF) 56 Page - Murata Manufacturing Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
GRM552B11H102KA01D 데이터시트(HTML) 56 Page - Murata Manufacturing Co., Ltd. |
|
|
56 / 221 page  Continued from the preceding page. Continued on the following page. Temperature Step 100 to 120 °C 170 to 200 °C Time 1 min. 1 min. 1 2 1 Step Min. Operating Temp. +0/–3 30 ±3 2 Room Temp. 2 to 3 3 Max. Operating Temp. +3/–0 30 ±3 4 Room Temp. 2 to 3 Temp. ( °C) Time (min.) Fix the capacitor to the supporting jig in the same manner and under the same conditions as (10). Perform the five cycles according to the four heat treatments shown in the following table. Set for 24 ±2 hours at room temperature, then measure. •Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/–10 °C for one hour and then set at room temperature for 24 ±2 hours. Perform the initial measurement. 15 Temperature Cycle The measured and observed characteristics should satisfy the specifications in the following table. Appearance No defects or abnormalities Capacitance Change Within ±2.5% or ±0.25pF (whichever is larger) B1, B3, R1, R6, R7, C8: Within ±7.5% F1, F5, E4: Within ±20% Q/D.F. 30pF and over: Q U1000 30pF and below: Q U400+20C C: Nominal Capacitance (pF) [B1, B3, R6, R7, C8] W.V.: 100V : 0.025 max. (C F0.068µF) : 0.05 max. (C U0.068µF) W.V.: 50/35/25V: : 0.025 max.* *GRM32D R7/R6/C8 1E106: 0.035 max. W.V.: 16/10V: 0.035 max. W.V.: 6.3/4V : 0.05 max. (C F3.3µF) : 0.1 max. (C U3.3µF) [E4] W.V.: 25Vmin: 0.05 max. [F1, F5] W.V.: 25V min. : 0.05 max. (C F0.1µF) : 0.09 max. (C U0.1µF) W.V.: 16/10V: 0.125 max. W.V.: 6.3V: 0.15 max. I.R. More than 10,000M Ω or 500Ω · F (whichever is smaller) Dielectric Strength No defects Preheat the capacitor at 120 to 150 °C for 1 minute. Immerse the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder solution at 270 ±5°C for 10±0.5 seconds. Set at room temperature for 24 ±2 hours, then measure. •Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/–10 °C for one hour and then set at room temperature for 24 ±2 hours. Perform the initial measurement. •Preheating for GRM32/43/55 14 Resistance to Soldering Heat The measured and observed characteristics should satisfy the specifications in the following table. Appearance No defects or abnormalities Capacitance Change Within ±2.5% or ±0.25pF (whichever is larger) B1, B3, R1, R6, R7, C8: Within ±7.5% F1, F5, E4: Within ±20% Q/D.F. 30pF and over: Q U1000 30pF and below: Q U400+20C C: Nominal Capacitance (pF) [B1, B3, R6, R7, C8] W.V.: 100V : 0.025 max. (C F0.068µF) : 0.05 max. (C U0.068µF) W.V.: 50/35/25V: : 0.025 max.* *GRM32D R7/R6/C8 1E106: 0.035 max. W.V.: 16/10V: 0.035 max. W.V.: 6.3/4V : 0.05 max. (C F3.3µF) : 0.1 max. (C U3.3µF) [E4] W.V.: 25Vmin: 0.025 max. [F1, F5] W.V.: 25V min. : 0.05 max. (C F0.1µF) : 0.09 max. (C U0.1µF) W.V.: 16/10V: 0.125 max. W.V.: 6.3V: 0.15 max. I.R. More than 10,000M Ω or 500Ω · F (whichever is smaller) Dielectric Strength No defects No. Test Method Specifications Temperature Compensating Type High Dielectric Type Item GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection 54 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. (Note 1) These Specifications and Test Methods indicate typical inspection. Please refer to individual specifications (our product specifications or the approval sheet). When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1). When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2). • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. !Note C02E.pdf 10.12.20 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
