AP160

Version 0.0

17

AMIC Technology, Inc.

ABSOLUTE MAXIMUM RATINGS

Parameter

Rating

Unit

Operating temperature under bias

-55 to +125

°C

Storage temperature range

-65 to +150

°C

Voltage on EA/V PP pin to V SS

0 to +12.5

V

Voltage on any other pin to V SS

-0.1 to +7.0

V

Maximum Operating Voltage

6.0

V

Maximum I OL per I/O pin

15.0

mA

NOTICE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This

This is a stress rating only and functional operation of the device at these or any other conditions beyond those

indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

DC CHARACTERICSTICS

The values shown in this table are valid for

Symbol

Parameter

Condition

Min

Max

Units

IL

V

Input Low Voltage

(Except EA)

-0.5

0.2 VCC-0.1

V

IL1

V

Input Low Voltage (EA)

-0.5

0.2 VCC-0.3

V

IH

V

Input High Voltage

(Except XTAL1, RST)

0.2 VCC+0.9

VCC+0.5

V

IH1

V

Input High Voltage

(XTAL1, RST)

0.7 VCC

VCC+0.5

V

OL

V

Output Low Voltage

(Ports 1,2,3)

OL

I

= 1.6mA

0.45

V

OL1

V

Output Low Voltage

(Port 0, ALE, PSEN)

OL

I

= 3.2mA

0.45

V

OH

I

=-60uA, VCC=5V±10%

2.4

V

OH

I

=-25uA

0.75 VCC

V

OH

V

Output High Voltage

(Port 1,2,3, ALE, PSEN)

OH

I

=-10uA

0.9 VCC

V

OH

I

=-800uA, VCC=5V±10%

2.4

V

OH

I

=-300uA

0.75 VCC

V

OH1

V

Output High Voltage

(Port 0 in External Bus Mode)

OH

I

=-80uA

0.9 VCC

V

IL

I

Logical 0 Input Current

(Ports 1,2,3)

IN

V =0.45V

-50

uA

TL

I

Logical 1 to 0 Transition Current

(Ports 1,2,3)

IN

V =2V, VCC=5V±10%

-650

uA

LI

I

Input Leakage Current

(Port 0, EA)

0.45<

IN

V

< VCC

±10

uA

RRST

Reset Pulldown Resistor

50

300

IO

C

Pin Capacitance

Test Freq. =1 MHZ,

A

10

PF

Active Mode, 12 MHZ

25

mA

Power Supply Current

Idle Mode, 12MHZ

6.5

mA

VCC = 5.5V

100

uA

CC

I

Power Down Mode

VCC = 3V

40

uA

Notes: 1. Under steady state (non-transient) conditions,

OL

I

must be externally limited as follows:

Maximum

OL

I

per port pin: 10mA

Maximum

OL

I

per 8-biit port: Port 0: 26mA, Ports 1,2,3: 15mA

Maximum total

OL

I

for all output pins: 71mA

If

OL

I

exceeds the test condition,

OL

V

may exceed the related specification. Pins are not guaranteed to sink currenr

greater than the listed test condition.

2. Minimum VCC for Power Down is 2V.