| 전자부품 데이터시트 검색엔진 |
|
TSL2671 데이터시트(PDF) 16 Page - ams AG |
|
|
|||||||||||||||||||||||||||||
TSL2671 데이터시트(HTML) 16 Page - ams AG |
|
16 / 27 page ![]() TSL2671 DIGITAL PROXIMITY DETECTOR TAOS118 − JANUARY 2011 15 The LUMENOLOGY r Company r r Copyright E 2011, TAOS Inc. www.taosinc.com Command Register The command registers specifies the address of the target register for future write and read operations. Table 2. Command Register 6 75 4 ADD 2 31 0 COMMAND COMMAND TYPE − − FIELD BITS DESCRIPTION COMMAND 7 Select Command Register. Must write as 1 when addressing COMMAND register. TYPE 6:5 Selects type of transaction to follow in subsequent data transfers: FIELD VALUE DESCRIPTION 00 Repeated byte protocol transaction 01 Auto-increment protocol transaction 10 Reserved — Do not use 11 Special function — See description below Transaction type 00 will repeatedly read the same register with each data access. Transaction type 01 will provide an auto-increment function to read successive register bytes. ADD 4:0 Address register/special function register. Depending on the transaction type, see above, this field either specifies a special function command or selects the specific control-status-register for following write and read transactions: FIELD VALUE DESCRIPTION 00000 Normal — no action 00101 Proximity interrupt clear Proximity Interrupt Clear clears any pending proximity interrupt. This special function is self clearing. Enable Register (0x00) The ENABLE register is used to power the device on/off, enable functions, and interrupts. Table 3. Enable Register 6 75 4 PON 2 31 0 ENABLE Reserved Resv Reserved Address 0x00 PIEN WEN PEN FIELD BITS DESCRIPTION Reserved 7:6 Reserved. Write as 0. PIEN 5 Proximity interrupt mask. When asserted, permits proximity interrupts to be generated. Reserved 4 Reserved. Write as 0. WEN 3 Wait Enable. This bit activates the wait feature. Writing a 1 activates the wait timer. Writing a 0 disables the wait timer. PEN 2:1 Proximity enable. These bits activate the proximity function. Writing a 11b enables proximity. Writing a 00b disables proximity. The Wait Time register should be configured before asserting proximity enable. PON 1, 2 0 Power ON. This bit activates the internal oscillator to permit the timers and ADC channel to operate. Writing a 1 activates the oscillator. Writing a 0 disables the oscillator. NOTES: 1. See Power Management section for more information. 2. A minimum interval of 2.72 ms must pass after PON is asserted before proximity can be initiated. This required time is enforced by the hardware in cases where the firmware does not provide it. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |