전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AT27C1024-45VC 데이터시트(PDF) 2 Page - ATMEL Corporation

부품명 AT27C1024-45VC
상세설명  1-Megabit 64K x 16 OTP EPROM
PDF  9 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  ATMEL [ATMEL Corporation]
홈페이지  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

AT27C1024-45VC 데이터시트(HTML) 2 Page - ATMEL Corporation

  AT27C1024-45VC Datasheet HTML 1Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 2Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 3Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 4Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 5Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 6Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 7Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 8Page - ATMEL Corporation AT27C1024-45VC Datasheet HTML 9Page - ATMEL Corporation  
Zoom Inzoom in Zoom Outzoom out
 2 / 9 page
background image
AT27C1024
2
In read mode, the AT27C1024 typically consumes 15 mA.
Standby mode supply current is typically less than 10
µA.
The AT27C1024 is available in industry standard JEDEC-
approved one-time programmable (OTP) plastic PDIP,
PLCC, and TSOP packages. The device features two-line
control (CE, OE) to eliminate bus contention in high-speed
systems.
With high density 64K word storage capability, the
AT27C1024 allows firmware to be stored reliably and to be
accessed by the system without the delays of mass storage
media.
Atmel’s 27C1024 have additional features to ensure high
quality and efficient production use. The Rapid™ Program-
ming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming
time is typically only 100
µs/word. The Integrated Product
Identification Code electronically identifies the device and
manufacturer. This feature is used by industry standard
programming equipment to select the proper programming
algorithms and voltages.
System Considerations
Switching between active and standby conditions via the
Chip Enable pin may produce transient voltage excursions.
Unless accommodated by the system design, these tran-
sients may exceed data sheet limits, resulting in device
non-conformance. At a minimum, a 0.1
µF high frequency,
low inherent inductance, ceramic capacitor should be uti-
lized for each device. This capacitor should be connected
between the VCC and Ground terminals of the device, as
close to the device as possible. Additionally, to stabilize the
supply voltage level on printed circuit boards with large
EPROM arrays, a 4.7
µF bulk electrolytic capacitor should
be utilized, again connected between the VCC and Ground
terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected
to the array.



Html Pages

1 2 3 4 5 6 7 8 9


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com