| 전자부품 데이터시트 검색엔진 |
|
OPA690 데이터시트(PDF) 12 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
OPA690 데이터시트(HTML) 12 Page - Texas Instruments |
|
12 / 27 page ![]() OPA3692 SBOS228E 12 www.ti.com HIGH-SPEED INSTRUMENTATION AMPLIFIER Figure 3 shows an instrumentation amplifier based on the OPA3692. The offset matching between inputs makes this an attractive input stage for this application. The differential-to- single-ended gain for this circuit is 2.0V/V. The inputs are high impedance, with only 1pF to ground at each input. The loads on the OPA3692 outputs are equal for the best harmonic distortion possible. 1/3 OPA3692 1/3 OPA3692 1/3 OPA3692 402 Ω 402 Ω 402 Ω 402 Ω 402 Ω 200 Ω 200 Ω 402 Ω V 2 V OUT V 1 1/3 OPA3692 402 Ω 402 Ω 100 Ω V 1 1/3 OPA3692 402 Ω 402 Ω 100 Ω V 2 1/3 OPA3692 402 Ω 402 Ω 100 Ω V 3 Selection Logic ADS826 10-Bit 60MSPS 0.1 µF 0.1 µF 4.99k Ω 0.1 µF 4.99k Ω 0.1 µF 100pF REFT +3.5V REFB +1.5V +In –In CM FIGURE 3. High-Speed Instrumentation Amplifier. FIGURE 5. Multiplexed Converter Driver. As shown in Figure 4, the OPA3692 used as an instrumenta- tion amplifier has a 240MHz, –3dB bandwidth. This plot has been made for a 1Vp-p output signal using a low-impedance differential input source. FIGURE 4. High-Speed Instrumentation Amplifier Response. 7 6 5 4 3 2 1 0 –1 –2 –3 Frequency (MHz) 1400 10 100 20log V OUT |V 1 – V2| MULTIPLEXED CONVERTER DRIVER The converter driver in Figure 5 multiplexes among the three input signals. The OPA3692s enable and disable times support multiplexing among video signals. The make-before- break disable characteristic of the OPA3692 ensures that the output is always under control. To avoid large switching glitches, switch during the sync or retrace portions of the video signal—the two inputs should be almost equal at these times. The output is always under control, so the switching glitches for two 0V inputs are < 20mV. With standard video signals levels at the inputs, the maximum differential voltage across the disabled inputs will not exceed the ±1.2V maximum rating. The output resistors isolate the outputs from each other when switching between channels. The feedback network of the disabled channels forms part of the load seen by the enabled amplifier, attenuating the signal slightly. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |