L6717TR datasheet(9/56 Pages) STMICROELECTRONICS

9 / 56 page

L6717

Pins description and connection diagrams

Doc ID 17326 Rev 1

9/56

CORE error amplifier inverting input.

Connect with a resistor RFB to VSEN and with an RF - CF to COMP. Droop current for

voltage positioning is sourced from this pin.

6VSEN

CORE output voltage monitor.

It manages OVP and UVP protections and PWRGOOD. Connect to the positive side

of the load for remote sensing. See Section 8 for details.

7FBG

CORE remote ground sense.

Connect to the negative side of the load for remote sensing. See Section 11 for proper

layout of this connection.

8LTB

LTB Technology® input pin.

Connect through an RLTB - CLTB network to the regulated voltage (CORE section) to

detect load transient. See Section 12 for details.

NB_COMP

NB error amplifier output.

Connect with an RF_NB - CF_NB to NB_FB.

The NB section and/or the device cannot be disabled by grounding this pin.

NB_FB

NB error amplifier inverting input.

Connect with a resistor RFB_NB to NB_VSEN and with an RF_NB - CF_NB to NB_COMP.

Droop current for voltage positioning is sourced from this pin.

NB_VSEN

NB output voltage monitor.

It manages OVP and UVP protections and PWRGOOD. Connect to the positive side

of the NB load to perform remote sensing. See Section 11 for proper layout of this

connection.

NB_FBG

NB remote ground sense.

Connect to the negative side of the load to perform remote sense. See Section 11 for

proper layout of this connection.

ILIM

CORE over current pin.

A current ILIM=DCR/RG*IOUT proportional to the current delivered by the CORE

Section is sourced from this pin. The OC threshold is programmed by connecting a

resistor RILIM to SGND. When the generated voltage crosses the OC_TOT threshold

(VOC_TOT = 2.5V Typ) the device latches with all MOSFETs OFF (to recover, cycle

VCC or the EN pin).

This pin is monitored for dynamic phase management.

Filter with proper capacitor to provide OC masking time; do not exceed 30

μsec. See

Section 8.4.1 for details.

OSC / EN /

FLT

OSC: It allows programming the switching frequency FSW of both sections. Switching

frequency can be increased according to the resistor ROSC connected to SGND with a

gain of 9.1kHz/µA (see Section 9 for details). If floating, the switching frequency is

200kHz per phase.

EN: Pull-low (tie to GND) to disable the device. When set free, the device immediately

checks for the VID1 status to determine the SVI / PVI protocol to be adopted and

configures itself accordingly.

FLT: The pin is internally forced high (3.3V) in case of an OV / UV fault. To recover

from this condition, cycle VCC or the EN pin.

To enable/disable the IC drive OSC/EN/FAUT pin by an open drain circuit.

Table 2.

Pin description (continued)

Pin#

Name

Function

L6717TR 데이터시트(PDF) 9 Page - STMicroelectronics

L6717TR 데이터시트(HTML) 9 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

데이터시트 다운로드

링크 URL