| 전자부품 데이터시트 검색엔진 |
|
1725672 데이터시트(PDF) 7 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
1725672 데이터시트(HTML) 7 Page - List of Unclassifed Manufacturers |
|
7 / 8 page ![]() PERFORMANCE PLOTS 7 REVISION N0. 002 REVISION DATE: 01-23-2013 EHE004 D9 GND BAT43W J3 SW1 P$6 P$1 P$2 P$3 P$4 P$5 QPXX_RA SW3 1 2 3 J4 2 VNS0 VNS1 4 5 6 VIN2 SW2 SW2 GND 1 2 3 CAS-D20 GND VCAP C2 C100 C101 + PAD 9 8 7 6 2 1 PZ1 PZ2 CAP VIN SW GND PGOOD D0 D1 VIN2 VOUT 3 4 5 U1 GND V+ PGOOD VCAP GND VOS0 VOS1 4.7uF VIN2 10uH C3 47uF C4 DNP GND PGOOD LTC3588MSE L1 P$4 P$3 P$2 P$1 J1 SW2: Output Voltage Select VOS1 0 0 1 1 0 1 0 1 1.8V 2.5V 3.3V 3.6V 3.45V 4.1V 4.5V 5.0V VOS0 3588-1 3588-2 Volture V2xx pin 1-4 is as follows: Piezo wafers on pin 1&2, 3&4 SW3/J4 “Superseries” select 1-2: Normal bridges operation 2-3: Halfbridge operation SW1: Piezo Conection Down: Wafers in parallel Up: Wafers in series Volture™ Product A B without J3 Connector B with J3 Connector V20W / V25W 1.250 0.588 0.986 V21B / V21BL 0.600 0.633 1.031 V22B / V22BL N/A N/A N/A V20W / V25W 1.250 0.588 0.986 V21B / V21BL 0.600 0.633 1.031 V22B / V22BL N/A N/A N/A Figure 2: EHE004 Board dimensions when used with one of Mide’s Volture energy harvesters. Maximum component height on the board is 0.10”. All dimensions are in inches. 0.100 0.700 A 1.450 1.600 EHE004 VOLTURE PRODUCT 2 X 0.089 2-56 THRU B the only setting that was able to provide any output was the Superseries, Parallel setting. From approximately 0.175 gee to 0.25 gee the Normal, Series setting was best. For all amplitudes above 0.25 gee the Normal, Parallel was the most efficient. It should be noted that these curves will vary substantially depending on the product that is used as well as the tip mass that is used to tune the product. In conclusion what this representative curve shows is that the piezo’s output energy and voltage for certain settings will allow the system to operate closer to the half open circuit voltage causing more efficient operation. For low level vibration the series setting is needed to get the piezo voltage output to reach the minimum voltage to operate the EHE004. BOARD SCHEMATIC AND DIMENSIONS Figure 2b: EHE004 Schematic |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |