| 전자부품 데이터시트 검색엔진 |
|
CS5101A 데이터시트(PDF) 28 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5101A 데이터시트(HTML) 28 Page - Cirrus Logic |
|
28 / 40 page ![]() shows a histogram plot of output code occur- rences obtained from 8192 samples taken from a CS5101A in the bipolar mode. Hexadecimal code 7FFE was arbitrarily selected and the analog in- put was set close to code center. With a noiseless converter, code 7FFE would always appear. The histogram plot of the device has a "bell" shape with all codes other than 7FFE due to internal noise. Figure 22 illustrates the noise histogram of the CS5102A. In a sampled data system all information about the analog input applied to the sample/hold ap- pears in the baseband from dc to one-half the sampling rate. This includes high-frequency com- ponents which alias into the baseband. Low-pass (anti-alias) filters are therefore used to remove frequency components in the input signal which are above one-half the sample rate. However, all wideband noise introduced by the CS5101A and CS5102A still aliases into the baseband. This "white" noise is evenly spread from dc to one- half the sampling rate and integrates to 35 µV rms in unipolar mode. Noise in the digital domain can be reduced by sampling at higher than the desired word rate and averaging multiple samples for each word. Over- sampling spreads the device’s noise over a wider band (for lower noise density), and averaging ap- plies a low-pass response which filters noise above the desired signal bandwidth. In general, the device’s noise performance can be maximized in any application by always sampling at the maximum specified rate of 100 kHz (CS5101A) or 20 kHz (CS5102A) (for lowest noise density) and digitally filtering to the desired signal band- width. Aperture Jitter Track-and-hold amplifiers commonly exhibit two types of aperture jitter. The first, more appropri- ately termed "aperture window", is an input voltage dependent variation in the aperture delay. Its signal-dependency causes distortion at high frequencies. The proprietary architecture of the CS5101A and CS5102A avoids applying the in- put voltage across a sampling switch, thus avoiding any "aperture window" effects. The sec- ond type of aperture jitter, due to component noise, assumes a random nature. With only 100 ps peak-to-peak aperture jitter, the CS5101A and CS5102A can process full-scale signals up to 7FFC 7FFD 7FFE 8000 8001 7FFF 7FFB 2048 4096 6144 8192 Count Noiseless CS5101A Code (Hexadecimal) Counts: 0 0 989 6359 844 0 0 Converter Figure 21. 5101A Histogram Plot of 8192 Conversion Inputs 7FFE 7FFF 8000(H) 8002 8003 8001 7FFD Count Noiseless CS5102A Code (Hexadecimal) Counts: 05 1727 4988 1467 5 0 Converter 8192 6144 4096 2048 Figure 22. 5102A Histogram Plot of 8192 Conversion Inputs CS5101A CS5102A 28 DS45F2 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |