| 전자부품 데이터시트 검색엔진 |
|
WDBR2 데이터시트(PDF) 3 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
WDBR2 데이터시트(HTML) 3 Page - List of Unclassifed Manufacturers |
|
3 / 4 page ![]() Ultra Low Profile Power Resistors WDBR Series www.bitechnologies.com www.irctt.com www.welwyn-tt.com General Note TT electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT electronics’ own data and is considered accurate at time of going to print. © TT electronics plc 2.14 WDBR resistors may be customised in various ways including: ·Alternativeshapesanddimensionsupto406mmx406mm ·Integrationoftemperaturemeasurementelements ·Alternativeohmicvalues,tolerance&TCR ·Increaseddielectricwithstandvoltage ·CustombrakingresistorswithULapproval For a full Applications Note for dynamic braking see http://www.welwyn-tt.com/pdf/application_notes/WDBR.pdf MaximumSingle Overload Power 0.1 1 10 100 0.01 0.11 10 100 Duration of Overload (s) DBR1/2 DBR1 DB 2 DB 3 W DB 5 DB 7 Single Overload Energy Capacity 0.01 0.1 1 10 100 0.01 0.11 10 100 Duration of Overload (s) WDBR1/2 WDBR1 WDBR2 WDBR3 WDBR5 WDBR7 Overload Conditions Maximum peak current (A) W W W W W W R R R R Value (ohms) 12 15 20 22 25 47 50 100 150 WDBR1/2 15.2 15.2 7.6 7.6 7.6 7.6 7.6 7.6 WDBR1 21.6 21.6 21.6 8.3 8.3 8.3 8.3 8.3 8.3 WDBR2 20.3 20.3 7.6 7.6 7.6 7.6 7.6 7.6 7.6 WDBR3 25.4 25.4 25.4 25.4 11.4 11.4 11.4 11.4 11.4 WDBR5 25.4 25.4 25.4 25.4 25.4 10.2 10.2 10.2 10.2 WDBR7 44.5 44.5 44.5 44.5 44.5 20.3 20.3 20.3 20.3 Bolt Size Typical Tightening Torque (Nm) WDBR1/2 M2 0.6 WDBR1 M3 2 WDBR2 M5 2.5 WDBR3 M5 2.5 WDBR5 M5 3.5 WDBR7 M5 4 Application Notes A heatsink with thermal resistance ≤0.53°C/W will enable the component to operate at its continuous power rating. Thermal grease (e.g. Dow Corning DC340) should be used and the heatsink should have a surface finish of <6.3μm with flatness of <0.05mm. The resistor should be mounted using an appropriate bolt as listed in the table below. This should be tightened so as to bring the whole area of the steel substrate into intimate contact with the heatsink. The unmounted part is slightly bowed so that the centre is above the edges. Inadequate tightening will leave the centre out of contact with the heatsink, whilst over tightening can cause the edges to rise. The tightening torque required will depend on the fixings and heatsink used, but typical figures are given for guidance. WDBR resistors will fail safe (open circuit) under overload fault conditions and still maintain a 1kV dielectric withstand. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |