HIP0082AS2 datasheet(3/12 Pages) INTERSIL

3 / 12 page

Absolute Maximum Ratings TA = 25oC

Thermal Information

Supply Voltage (Logic and Control), VCC . . . . . . . . . . . . -0.3V to 7V

Power MOSFET Drain Voltage, VO (Note 3) . . . . . . -0.7 to VCLAMP

Output Clamp Energy, EOK (See Note 5). . . . . . . . . . . . . . . . . 70mJ

Input Voltage (Logic and Driver Inputs), VIN. . . .-0.5V to VCC +0.5V

Maximum Output Current, Outputs 1 and 2 . . . . . . . . . . . . . . . . +2A

Maximum Output Current, Outputs 3 and 4 . . . . . . . . . . . . . . . . +5A

Maximum Total Output Current, All Outputs ON. . . . . . . . . . . . . +8A

Maximum Peak Output Current, IO(MAX), (Note 4) . . . . . -5A to ISC

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC

Thermal Resistance (Typical, Notes 5, 6, 7)

θJA (oC/W) θJC (oC/W)

Power SIP Package . . . . . . . . . . . . . . .

PSOP Package . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . -40oC to 150oC

Maximum Storage Temperature Range, TSTG . . . . -55

oC to 150oC

Maximum Lead Temperature (During Soldering 10s) . . . . . . 300oC

(PSOP - Lead Tips Only)

Die Characteristics

Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . .VSS (Tab Ground)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

3. The MOSFET Output Drain is internally clamped with a Drain-to-Gate zener diode that turns on the MOSFET to hold the Drain at the

VCLAMP voltage. Refer to the Electrical Specifications Table for the VCLAMP voltage limits.

4. Each Output has Over Current Shutdown protection in the positive current direction. The maximum peak current rating is set equal to the

minimum Over Current Shutdown as detailed in the Electrical Speciﬁcation Table. In the event of an Over Current Shutdown the input

drive is latched OFF. The output short must be removed and the input toggled OFF and ON to restore the output drive.

5. Refer to Application Note AN9416 for Single Pulse Energy and Device Dissipation rating information, including inductive load operation

and other thermal stress characterization.

θJA is measured with the component mounted on an evaluation PC board in free air.

7. Maximum PSOP Package Dissipation at 125oC with 26oC/W Heat Sink (6 sq cm Copper PCB) is 0.96W.

Electrical Speciﬁcations

VCC = 5V ±10%, TA = -40

oC to 125oC; Unless Otherwise Specified

PARAMETER

SYMBOL

TEST CONDITIONS

HIP0082

HIP0084

UNITS

MIN

TYP

MAX

MIN

TYP

MAX

POWER OUTPUTS

Output ON Resistance

(Normal Mode)

rDS(ON)1,

rDS(ON)2

Outputs 1 and 2, One Output ON,

IOUT = 2A, TJ = 150

0.62

Ω

rDS(ON)3,

rDS(ON)4

Outputs 3 and 4, One Output ON,

IOUT = 2A, TJ = 150

0.57

Ω

Output ON Resistance

(Normal Mode)

rDS(ON)1,

rDS(ON)2

Outputs 1 and 2, One Output ON,

IOUT = 2A, TJ = 75

N/A

0.5

Ω

Output ON Resistance

(Normal Mode)

rDS(ON)3,

rDS(ON)4

Outputs 3 and 4, One Output ON,

IOUT = 2A, TJ = 105

0.5

Ω

Output Zener Clamp Voltage

IOUT = 40mA

Matching Zener Clamp

Voltage

∆VZ

IOUT = 40mA, tZ = 100µs

N/A

±1.5

Output Short Current Limit,

Outputs 1 and 2 (Note 8)

ISC(L)

3.4

5.1

Output Short Current Limit,

Outputs 3 and 4 (Note 8)

ISC(L)

ISC Bit High

3.4

Output Short Current Limit,

Outputs 3 and 4 (Note 8)

ISC(H)

ISC Bit Low

7.5

8.3

Short Circuit Current Filter

Time

tSC

µs

Output Capacitance

VOUTX = 16V, f = 1MHz

250

HIP0082, HIP0084

HIP0082AS2 데이터시트(PDF) 3 Page - Intersil Corporation

HIP0082AS2 데이터시트(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

데이터시트 다운로드

링크 URL