전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

LT1793CS8 데이터시트(PDF) 9 Page - Linear Technology

부품명 LT1793CS8
상세설명  Low Noise, Picoampere Bias Current, JFET Input Op Amp
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  LINER [Linear Technology]
홈페이지  http://www.linear.com
Logo LINER - Linear Technology

LT1793CS8 데이터시트(HTML) 9 Page - Linear Technology

Back Button LT1793CS8 Datasheet HTML 4Page - Linear Technology LT1793CS8 Datasheet HTML 5Page - Linear Technology LT1793CS8 Datasheet HTML 6Page - Linear Technology LT1793CS8 Datasheet HTML 7Page - Linear Technology LT1793CS8 Datasheet HTML 8Page - Linear Technology LT1793CS8 Datasheet HTML 9Page - Linear Technology LT1793CS8 Datasheet HTML 10Page - Linear Technology LT1793CS8 Datasheet HTML 11Page - Linear Technology LT1793CS8 Datasheet HTML 12Page - Linear Technology  
Zoom Inzoom in Zoom Outzoom out
 9 / 12 page
background image
9
LT1793
S
APPLICATI
I FOR ATIO
Input:
±5.2V Sine Wave
LT1793 Output
LT1793 F05a
LT1793 F05b
Figure 5. Voltage Follower with Input Exceeding the Common Mode Range (VS = ±5V)
resulting in a change in voltage dV, which is equal to dQ/CF.
The gain therefore is CF/CS. For unity-gain, the CF should
equal the transducer capacitance plus the input capaci-
tance of the LT1793 and RF should equal RS.
In the noninverting mode example, the transducer current
is converted to a change in voltage by the transducer
capacitance, CS. This voltage is then buffered by the
LT1793 with a gain of 1 + R1/R2. A DC path is provided by
RS, which is either the transducer impedance or an exter-
nal resistor. Since RS is usually several orders of magni-
tude greater than the parallel combination of R1 and R2, RB
is added to balance the DC offset caused by the noninvert-
ing input bias current and RS. The input bias currents,
although small at room temperature, can create significant
errors at higher temperature, especially with transducer
resistances of up to 1000M or more. The optimum value
for RB isdeterminedbyequatingthethermalnoise(4kTRS)
to the current noise (2qIB) times RS2. Solving for RS
results in RB = RS = 2VT/IB (VT = 26mV at 25°C). A parallel
capacitor CB, is used to cancel the phase shift caused by
the op amp input capacitance and RB.
Reduced Power Supply Operation
To take full advantage of a wide input common mode range,
the LT1793 was designed to eliminate phase reversal.
Referring to the photographs in Figure 5, the LT1793 is
shown operating in the follower mode (AV = 1) at ±5V
supplies with the input swinging
±5.2V. The output of the
LT1793 clips cleanly and recovers with no phase reversal.
This has the benefit of preventing lockup in servo systems
and minimizing distortion components.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com