MAX2102CWI datasheet(2/16 Pages) MAXIM

2 / 16 page

AGC Input Bias Current

Direct-Conversion Tuner ICs for

Digital DBS Applications

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

DC ELECTRICAL CHARACTERISTICS

(VCC = +4.75V to +5.25V; GND = 0V; PSGND = GND; AGC = 1.3V; MOD = 0.8V; PRFIN = OFF, fLO = 1450.125MHz; PLO = -15dBm;

IOUT, QOUT = open; TA = 0°C to +70°C; unless otherwise noted.)

AC ELECTRICAL CHARACTERISTICS

(MAX2102 EV kit circuit (Figure 1); VCC = +5V; PSGND = open; MOD = GND; fRFIN = 2150MHz; PRFIN = -19dBm; fLO =

2150.125MHz; PLO = -15dBm driven single-ended into LO; AGC set via servo loop for VIOUT = VQOUT = 0.5Vp-p; IOUT, QOUT drive

AC-coupled 100

Ω loads; 2kΩ from PSOUT to GND; TA = +25°C; unless otherwise noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

VCC to GND ..............................................................-0.5V to +7V

RFIN to RFIN ..........................................................................±2V

LO to LO ................................................................................±2V

AGC, MOD, RFIN, RFIN, LO, LO to GND .....-0.5V to (VCC + 0.5V)

AGC Current. ....................................................................±30mA

IDC to IDC, QDC to QDC.......................................................±2V

IOUT or QOUT to GND Short-Circuit Duration ...................10sec

PSOUT to GND Short-Circuit Duration.................................None

IDC, IDC, QDC, QDC to GND ....................-0.5V to (VCC + 0.5V)

Continuous Power Dissipation (TA = +70°C)

SO (derate 12.5mW/°C above +70°C) ..........................1.025W

Operating Temperature Range...............................0°C to +70°C

Junction Temperature ......................................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10sec) .............................+300°C

MAX2102

≤ VMOD ≤ VCC

CONDITIONS

150

195

Quiescent Supply Current

4.75

5.25

Operating Supply Voltage Range

2.2

2.6

IOUT, QOUT Common-Mode Voltage

-250

180

0.8

MOD Input Low Level

2.0

MOD Input High Level

µA

-80

MOD Input Bias Current

UNITS

MIN

TYP

MAX

PARAMETER

Refers to single-carrier power generating

VIOUT = VQOUT = 0.5Vp-p,

950MHz < fRFIN < 2150MHz,

950MHz < fLO < 2150MHz (Note 2)

(Note 1)

Refers to single-carrier power generating

VIOUT = VQOUT = 0.5Vp-p,

950MHz < fRFIN < 2150MHz,

950MHz < fLO < 2150MHz (Note 2)

CONDITIONS

dBm

RFIN Maximum Single-Carrier

Input Power

MHz

950

2150

RFIN Carrier Frequency Range

dBm

-69

RFIN Minimum Single-Carrier

Input Power

UNITS

MIN

TYP

MAX

PARAMETER

-19

MAX2102

MAX2105

-60

0.5V

≤ VAGC ≤ 4V

AGC Range

MAX2102

MAX2105

RF FRONT END

MAX2105

µA

-180

180

AGC Input Bias Current

SUPPLY

CONTROL INPUTS, PRESCALER

0.5V

≤ VAGC ≤ 4V

MAX2102CWI 데이터시트(PDF) 2 Page - Maxim Integrated Products

MAX2102CWI 데이터시트(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

데이터시트 다운로드

링크 URL