전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

MAX382C/D 데이터시트(PDF) 10 Page - Maxim Integrated Products

부품명 MAX382C/D
상세설명  Low-Voltage, 8-Channel/Dual 4-Channel Multiplexers with Latchable Inputs
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  MAXIM [Maxim Integrated Products]
홈페이지  https://www.maximintegrated.com/en.html
Logo MAXIM - Maxim Integrated Products

MAX382C/D 데이터시트(HTML) 10 Page - Maxim Integrated Products

Back Button MAX382C/D Datasheet HTML 4Page - Maxim Integrated Products MAX382C/D Datasheet HTML 5Page - Maxim Integrated Products MAX382C/D Datasheet HTML 6Page - Maxim Integrated Products MAX382C/D Datasheet HTML 7Page - Maxim Integrated Products MAX382C/D Datasheet HTML 8Page - Maxim Integrated Products MAX382C/D Datasheet HTML 9Page - Maxim Integrated Products MAX382C/D Datasheet HTML 10Page - Maxim Integrated Products MAX382C/D Datasheet HTML 11Page - Maxim Integrated Products MAX382C/D Datasheet HTML 12Page - Maxim Integrated Products  
Zoom Inzoom in Zoom Outzoom out
 10 / 12 page
background image
Low-Voltage, 8-Channel/Dual 4-Channel
Multiplexers with Latchable Inputs
10
______________________________________________________________________________________
VGEN
GND
WR
CL
100pF
VOUT
-5V
V-
V+
RGEN
VOUT
EN
ON
OFF
OFF
∆VOUT
∆VOUT IS THE MEASURED VOLTAGE ERROR DUE TO
CHARGE INJECTION. THE CHARGE IN COULOMBS IS Q = CL x ∆VO
+5V
N0_
IN
+2.4V
3V
A0, A1, (A2)
COM
RS
MAX382
MAX384
Figure 7. Charge Injection (VCTE)
GND
WR
35pF
VOUT
-5V
V-
V+
VO
VOUT
+3V
+1.5V
0V
RS
tOFF (RS)
50%
0.8VO
+5V
EN
RS
1k
+5V
A0, A1,
(A2)
N01–
N08
COM, COMB
LOGIC
INPUT
N01
+2.4V
MAX382
Figure 6. Reset Turn-Off Time (tOFF(RS))
Operation with Supply Voltages
Other than ±5V
Using supply voltages less than ±5V reduces the analog
signal range. The MAX382/MAX384 muxes operate with
±3V to ±8V bipolar supplies or with a +2.7V to +16.5V
single supply. Connect V- to GND when operating with a
single supply. Both devices can also operate with unbal-
anced supplies, such as +10V and -5V. The
Typical
Operating Characteristics graphs show typical on-resis-
tance with ±3V, ±5V, +3V and +5V supplies. (Switching
times increase by a factor of two or more for operation at
+5V or below.)
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
is not possible, add two small signal diodes (D1, D2) in
series with supply pins for overvoltage protection
(Figure 8). Adding diodes reduces the analog signal
range to one diode drop below V+ and one diode drop
above V-, but does not affect the devices’ low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between V+
and V- should not exceed 17V. These protection diodes
are not recommended when using a single supply.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com