ICS8530-01 datasheet(4/17 Pages) IDT

4 / 17 page

ICS8530FY-01 REVISION G NOVEMBER 15, 2012

ICS8530-01 Data Sheet

LOW SKEW, 1-TO-16, DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER

Table 4B. Differential Input DC Characteristics, VCC = VCCO = 3.3V ± 5%, VEE = 0V, TA = 0°C to 70°C

NOTE 1: VIL should not be less than -0.3V.

NOTE 2: Common mode input voltage is defined as VIH.

Table 4C. LVPECL DC Characteristics, VCC = VCCO = 3.3V ± 5%, VEE = 0V, TA = 0°C to 70°C

NOTE 1: Outputs terminated with 50

 to V

CCO – 2V.

AC Electrical Characteristics

Table 5. AC Electrical Characteristics, VCC = VCCO = 3.3V ± 5%, VEE = 0V, TA = 0°C to 70°C

NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when device is

mounted in a test socket with maintained transverse airflow greater than 500 lfpm. Device will meet specifications after thermal equilibrium has

been reached under these conditions.

NOTE All parameters measured at 250MHz unless noted otherwise.

NOTE 1: Measured from the differential input crossing point to the differential output crossing point.

NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.

NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at the differential cross

points.

NOTE 4: Defined as skew between outputs on different devices operating at the same supply voltage, same temperature, same frequency

and with equal load conditions. Using the same type of inputs on each device, the outputs are measured at the differential cross points.

Symbol

Parameter

Test Conditions

Minimum

Typical

Maximum

Units

IIH

Input High Current

CLK

VIN = VCC = 3.465V

150

µA

nCLK

VIN = VCC = 3.465V

µA

IIL

Input Low Current

CLK

VIN = 0V, VCC = 3.465V

-5

µA

nCLK

VIN = 0V, VCC = 3.465V

-150

µA

VPP

Peak-to-Peak Input Voltage; NOTE 1

0.15

1.3

VCMR

Common Mode Input Voltage; NOTE 1, 2

VEE + 0.5

VCC – 0.85

Symbol

Parameter

Test Conditions

Minimum

Typical

Maximum

Units

VOH

Output High Voltage; NOTE 1

VCCO – 1.4

VCCO – 0.9

VOL

Output Low Voltage; NOTE 1

VCCO – 2.0

VCCO – 1.7

VSWING

Peak-to-Peak Output Voltage Swing

0.6

1.0

Symbol

Parameter

Test Conditions

Minimum

Typical

Maximum

Units

fMAX

Output Frequency

500

MHz

tJIT

Buffer Additive Phase Jitter,

RMS; refer to Additive Phase

Jitter Section

106.25MHz,

Integration Range: 12kHz – 20MHz

0.03

tPD

Propagation Delay; NOTE 1

 500MHz

tsk(o)

Output Skew; NOTE 2, 3

tsk(pp)

Part-to-Part Skew; NOTE 2, 4

148

305

tR / tF

Output Rise/ Fall Time

20% to 80% @ 50MHz

300

750

odc

Output Duty Cycle

ICS8530-01 데이터시트(PDF) 4 Page - Integrated Device Technology

ICS8530-01 데이터시트(HTML) 4 Page - Integrated Device Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

데이터시트 다운로드

링크 URL