PIC16LC62B datasheet(33/120 Pages) MICROCHIP

33 / 120 page

PIC16C62B/72A

Preliminary

DS35008B-page 33

7.0

CAPTURE/COMPARE/PWM

(CCP) MODULE

The CCP (Capture/Compare/PWM) module contains a

16-bit register, which can operate as a 16-bit capture

master/slave duty cycle register. Table 7-1 shows the

timer resources of the CCP module modes.

Capture/Compare/PWM Register 1 (CCPR1) is com-

prised of two 8-bit registers: CCPR1L (low byte) and

CCPR1H (high byte). The CCP1CON register controls

the operation of CCP1. All are readable and writable.

Additional information on the CCP module is available

in the PICmicro™ Mid-Range Reference Manual,

(DS33023).

TABLE 7-1

CCP MODE - TIMER

RESOURCE

TABLE 7-2

INTERACTION OF TWO CCP MODULES

CCP Mode

Timer Resource

Capture

Compare

PWM

Timer1

Timer2

CCPx Mode CCPy Mode

Interaction

Capture

Same TMR1 time-base.

Capture

Compare

The compare should be configured for the special event trigger, which clears TMR1.

Compare

The compare(s) should be configured for the special event trigger, which clears TMR1.

PWM

The PWMs will have the same frequency and update rate (TMR2 interrupt).

PWM

Capture

None.

PWM

Compare

None.

U-0

R/W-0

—

CCP1X

CCP1Y CCP1M3

CCP1M2

CCP1M1 CCP1M0

R = Readable bit

W = Writable bit

U = Unimplemented bit, read

as ‘0’

- n =Value at POR reset

bit7

bit0

bit 7-6:

Unimplemented: Read as '0'

bit 5-4: CCP1X:CCP1Y: PWM Least Significant bits

Capture Mode: Unused

Compare Mode: Unused

PWM Mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.

bit 3-0: CCP1M3:CCP1M0: CCP1 Mode Select bits

0000

= Capture/Compare/PWM off (resets CCP1 module)

0100

= Capture mode, every falling edge

0101

= Capture mode, every rising edge

0110

= Capture mode, every 4th rising edge

0111

= Capture mode, every 16th rising edge

1000

= Compare mode, set output on match (CCP1IF bit is set)

1001

= Compare mode, clear output on match (CCP1IF bit is set)

1010

= Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected)

1011

= Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1 and starts an A/D

conversion (if A/D module is enabled))

11xx

= PWM mode

PIC16LC62B 데이터시트(PDF) 33 Page - Microchip Technology

PIC16LC62B 데이터시트(HTML) 33 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL