PIC16F84A datasheet(76/124 Pages) MICROCHIP

76 / 124 page

PIC16F8X

PIC16F83/84

DS30430C-page 76

10.2

DC CHARACTERISTICS:

PIC16LF84, PIC16LF83 (Commercial, Industrial)

DC Characteristics

Power Supply Pins

Standard Operating Conditions (unless otherwise stated)

Operating temperature

°C ≤ TA ≤ +70°C (commercial)

-40

°C ≤ TA ≤ +85°C (industrial)

Parameter

No.

Sym

Characteristic

Min

Typ† Max Units

Conditions

D001

VDD

Supply Voltage

2.0

—

6.0

XT, RC, and LP osc conﬁguration

D002

VDR

RAM Data Retention

Voltage(1)

1.5*

—

Device in SLEEP mode

D003

VPOR

VDD start voltage to

ensure internal

Power-on Reset signal

—

VSS

—

See section on Power-on Reset for details

D004

SVDD

VDD rise rate to ensure

internal Power-on

Reset signal

0.05*

—

V/ms See section on Power-on Reset for details

D010

D010A

D014

IDD

Supply Current(2)

—

7.3

µA

RC and XT osc conﬁguration(4)

FOSC = 2.0 MHz, VDD = 5.5V

(During Flash programming)

LP osc conﬁguration

FOSC = 32 kHz, VDD = 2.0V,

WDT disabled

D020

D021

D021A

IPD

Power-down Current(3)

—

3.0

0.4

7.0

9.0

µA

VDD = 2.0V, WDT enabled, industrial

VDD = 2.0V, WDT disabled, commercial

VDD = 2.0V, WDT disabled, industrial

These parameters are characterized but not tested.

†

Data in "Typ" column is at 5.0V, 25

°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.

2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin

loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an

impact on the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, T0CKI = VDD,

MCLR = VDD; WDT enabled/disabled as speciﬁed.

3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is

measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.

4: For RC osc conﬁguration, current through Rext is not included. The current through the resistor can be

estimated by the formula IR = VDD/2Rext (mA) with Rext in kOhm.

PIC16F84A 데이터시트(PDF) 76 Page - Microchip Technology

PIC16F84A 데이터시트(HTML) 76 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL