전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

CMPWR280TO 데이터시트(PDF) 6 Page - ON Semiconductor

부품명 CMPWR280TO
상세설명  Dual Input SmartOR POWER Switch
PDF  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  ONSEMI [ON Semiconductor]
홈페이지  http://www.onsemi.com
Logo ONSEMI - ON Semiconductor

CMPWR280TO 데이터시트(HTML) 6 Page - ON Semiconductor

Back Button CMPWR280TO Datasheet HTML 2Page - ON Semiconductor CMPWR280TO Datasheet HTML 3Page - ON Semiconductor CMPWR280TO Datasheet HTML 4Page - ON Semiconductor CMPWR280TO Datasheet HTML 5Page - ON Semiconductor CMPWR280TO Datasheet HTML 6Page - ON Semiconductor CMPWR280TO Datasheet HTML 7Page - ON Semiconductor CMPWR280TO Datasheet HTML 8Page - ON Semiconductor CMPWR280TO Datasheet HTML 9Page - ON Semiconductor CMPWR280TO Datasheet HTML 10Page - ON Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 11 page
background image
CMPWR280
http://onsemi.com
6
VCC Supply Current of the device is shown across the
entire VCC range in V.
In the absence of VAUX, the supply current remains fixed
at approximately 0.15 mA until VCC reaches the Select
voltage threshold of 4.35 V. At this point the regulator is
enabled and a supply current of 1.0 mA is conducted.
When VAUX is present, the VCC supply current is less than
10
mA until VCC exceeds VAUX, at which point VCC then
powers the controller (0.15 mA). When VCC reaches
VSELECT, the regulator is enabled.
Figure 5. VCC Supply Current (No Load)
TYPICAL TRANSIENT CHARACTERISTICS
The transient characterization test set−up shown in
Transient Performance Test Set−up includes the effective
source impedance of the VCC supply (RS). This was
measured to be approximately 0.1
W. It is recommended that
this effective source impedance be no greater than 0.15
W to
ensure precise switching is maintained during VCC selection
and deselection.
Both the rise and fall times during VCC power−up/down
sequencing were controlled at a 10 millisecond duration.
This is considered to represent worst case conditions for
most application circuits.
During a selection or deselection transition, the DC load
current is switching from VAUX to VCC and vice versa. In
addition to the normal load current, there may also be an
in−rush current for charging/discharging the load capacitor.
The total current pulse being applied to either VAUX or
VCC is equal to the sum of the DC load and the
corresponding in−rush current. Transient currents in excess
of 1.0 amps can readily occur for brief intervals when either
supply commences to power the load.
VOUT
VSBY
VCC
GND
VOUT
0.1 mF10 mF
Load
2.2 W
PWR280
VCC
5 V
TR=20ms
TF=20ms
VSBY
5 V
Figure 6. Transient Characterization Test Set−up
+
+
+
+
Drive
+
VAUX
3.3 V
FDN338P
(Si2310DS)
0.1 mF1 mF
0.1 W
+
0.1 W
0.1 mF1 mF



Html Pages

1 2 3 4 5 6 7 8 9 10 11


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com