| 전자부품 데이터시트 검색엔진 |
|
MT9196AS 데이터시트(PDF) 5 Page - Mitel Networks Corporation |
|
|
|||||||||||||||||||||||||||||
MT9196AS 데이터시트(HTML) 5 Page - Mitel Networks Corporation |
|
5 / 38 page ![]() Preliminary Information MT9196 7-131 On PWRST (pin 5) the Filter/CODEC defaults such that the side-tone path, dial tone filter and 400 Hz transmit filter are off, all programmable gains are set to 0dB and CCITT µ-Law is selected. Further, the Filter/CODEC is powered down due to the control bits of the Path Control Registers (addresses 12h and 13h) being reset. The internal architecture is fully differential to provide the best possible noise rejection as well as to allow a wide dynamic range from a single 5 volt supply design. This fully differential architecture is continued into the Transducer Interface section to provide full chip realization of these capabilities for the handset and loudspeaker functions. A reference voltage (VRef), for the conversion requirements of the CODEC section, and a bias voltage (VBias), for biasing the internal analog sections, are both generated on-chip. VBias is also brought to an external pin so that it may be used for biasing external gain plan setting amplifiers. A 0.1 µF capacitor must be connected from VBias to analog ground at all times. Likewise, although VRef may only be used internally, a 0.1 µF capacitor from the VRef pin to ground is required at all times. The analog ground reference point for these two capacitors must be physically the same point. To facilitate this the VRef and VBias pins are situated on adjacent pins. The transmit filter is designed to meet CCITT G.714 specifications. The nominal gain for this filter path is 0 dB (gain control = 0 dB). Gain control allows the output signal to be increased up to 7 dB. An anti- aliasing filter is included. This is a second order lowpass implementation with a corner frequency at 25 kHz. Attenuation is better than 32 dB at 256 kHz and less than 0.01 dB within the passband. An optional 400Hz high-pass function may be included into the transmit path by enabling the Tfhp bit in the Control Register 1 (address 0Eh). This option allows the reduction of transmitted background noise such as motor and fan noise. Figure 3 - Audio Gain Partitioning SERIAL PORT DIGITAL GAIN & TONES FILTER/CODEC TRANSDUCER INTERFACE Handset Receiver (150 Ω) Speakerphone Speaker (40 Ω nominal) 34 Ω min) Digital Domain Analog Domain PCM PCM Receive -24 to +21 dB (3dB steps) DTMF, Tone Ringer -24 to +21 dB (3 dB steps) Receive Filter Gain 0 to -7 dB (1 dB steps) Side-tone -9.96 to +9 96dB -11 dB Transmit Filter Gain 0 to +7 dB (1 dB steps) (3.32 dB steps) -6 dB 0/+8dB +8 to -20dB (4 dB steps) RINGER 0 to -28 dB (4 dB steps) Trans- mit Gain Trans- mit Gain 6.37 dB M U X 5 dB 5 dB AUXin MIC+ M + M - AUXout AUX input H/F answer- back mic Transitter microphone Auxiliary Out Driver -12 dB Speaker Phone Driver 0 dB Receiver Driver -6.1 dB or -3.6 dB HSPKR + HSPKR - SPKR + SPKR - 75 75 Internal To Device External To Device Transmit -0.37 dB or 8.93 dB Din Dout |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |