| 전자부품 데이터시트 검색엔진 |
|
SM8580 데이터시트(PDF) 16 Page - Nippon Precision Circuits Inc |
|
|
|||||||||||||||||||||||||||||
SM8580 데이터시트(HTML) 16 Page - Nippon Precision Circuits Inc |
|
16 / 23 page ![]() SM8580AM NIPPON PRECISION CIRCUITS—16 Timer Registers (Bank 2, Registers 4 to 8, E) Timer control registers (registers 8, E) s TE bit (timer enable) Timer countdown stop/start control bit. When set to 1, the timer starts counting down. When set to 0 during countdown, the timer stops. s TF bit (timer flag) The timer flag is set to 1 when the timer counter counts down to zero, occurring a timer event. It is held at 1 until 0 is written to this bit. A 1 cannot be written to TF. s TIE bit (timer interrupt enable) This bit enables the timer interrupt output on TIRQN when a timer event is occurred. If the TIE is not set to 1, then no output occurs even if the TF bit is set to 1. The TIRQN output is high imped- ance when TIE is set to 0. s TI/TP bit (level/periodic interrupt mode select bit) Sets the timer interrupt signal output mode. The SM8580AM supports two timer function modes. • TI/TP = 0 (level interrupt mode) When a timer interrupt is occurred, TIRQN goes LOW (if TIE = 1) and TF is set to 1. TIRQN remains LOW and TF is held at 1 until a 0 is written to the TF bit. The timer operates by counting down until the data is zero, then the TE bit is cleared and the count stops automatically. However, if the timer is started when the TF bit is 1, then the TE bit is not cleared. The timer count register contents remain zero after the count down stops. • TI/TP = 1 (periodic interrupt mode) When a timer interrupt is occurred, TIRQN goes LOW (if TIE = 1) and TF is set to 1. TIRQN subsequently goes high impedance after a fixed interval, but TF is held at 1 until a 0 is written to the TF bit. The timer operates by counting down until the data is zero, then the timer register data is reloaded automatically after a fixed interval, and the countdown restarts. This mode can be used as a repetitive interval timer. Timer source clock set register (register 8) s The register 8 bits 0 and 1 set the timer source clock to one of four frequencies listed in the fol- lowing table. Bank A d dress Register Bit 3 Bit 2 Bit 1 Bit 0 2 8 Timer setting T E TI/TP E Timer control T F TIE Bank A d dress Register Bit 3 Bit 2 Bit 1 Bit 0 2 8 Timer setting T D 1 T D 0 T D 1 T D 0 Timer source clock 0 0 4096Hz 0 1 64Hz 1 0 1Hz 1 1 1/60Hz (1 minute) |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |