H7CX-R11W-N datasheet(16/56 Pages) OMRON

16 / 56 page

H7CX-A

@-N

Counter

Run mode

Power ON

Function

setting mode

*5 Displayed for output modes other than K-2, D, L, and H only.

*6 Displayed only when the input mode is

ud-a, ud-b, or ud-c.

(Not displayed when the function is set to

twn.)

Note: Displayed only when the output mode is C, R, K-1, P, Q, A,

or K-2.

Note: Displayed for terminal-block models (except H7CX-A11

@) only.

*3 When Using Dual Counter

Operation

*7 Set each digit using the individual

U (D) Keys.

Note: Displayed only when the

output mode is C, R, K-1, P, Q,

A, or K-2.

Note: Displayed for output modes

other than D, L, and H.

HOLD cannot be set when

the output mode is K-2.

*7 Set each digit using the individual

U (D) Keys.

Note: Displayed only when Twin Counter Mode is not selected.

(Red)

(Green) (Orange) (Red-green) (Green-red) (Red-orange) (Orange-red) (Green-orange) (Orange-green)

3 s min.*2

3 s min.*1

Step3

Parameters that cannot be set with the DIP switch are set with the operation keys on the front panel.

Change to Function Setting Mode.

Input mode

(CNTM)

Output

time

(OTIM)

Output mode

(OUTM)

NPN/PNP

input mode

(IMOD)

Display color

(COLR)

(1 ms)

(20 ms)

(No decimal point)

Prescale

value

(PSCL)

Counting

speed

(CNTS)

(30 Hz)

(5 kHz)

(PNP input)

(NPN input)

The characters displayed in reverse video are the default settings.

When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).

If pin 1 of the DIP switch is set to ON, the setting items indicated by

will not be displayed.

For 6-digit models, only

U Keys are provided.

Displays for 6-digit models are given in parentheses.

(N)

(0.50 s) (99.99 s)

(0.01 s)

(0.01 s) (99.99 s)

(Outputs held)

(F)

(C)

(R)

(K-1)

(P)

(Q)

(A)

(K-2)

(D)

(L)

(H)

(DOWN) (UP/DOWN A)(UP/DOWN B)(UP/DOWN C)

(UP)

(99.999)

(1.000)

(0.001)

(0.50 s) (99.99 s)

(0.01 s)

To next page

From next page

(Addition) (Subtraction)

Reset input

signal width

(IFLT)

Decimal

point position

(DP)

• Set the input mode using the

U (D) Keys.

• Set the output mode using the

U (D) Keys.

• Set each digit using the individual

U (D) Keys.

• Set the counting speed using the

U (D) Keys.

• Set the Reset input signal width using the

U (D) Keys.

• Set the decimal point position using the

U (D) Keys.

(One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

• Set each digit using the individual

U (D) Keys.

(9.999)

• Set the NPN/PNP input mode using the

U (D) Keys.

• Set the display color using the

U (D) Keys.

Dual count

calculating

mode

(ADD)

• Set the dual count calculating

mode using the

UD Keys.

*4 Displayed only when the output mode is K-2,

D, L, or H.

When using as a 2-stage preset counter

One-shot

output 2

time

(OTM2)

One-shot

output 1

time

(OTM1)

Note: Displayed only when the

output mode is C, R, K-1, P, Q,

A, or K-2.

(0.50 s) (99.99 s)

(0.01 s)

When using as a batch counter

One-shot

output 2

time

(OTM2)

grn

red

org

r-g

g-r

r-o

o-r

g-o

o-g

down

0.01

99.99

0.50

30hz

1ms

0.001

99.999

9.999

1.000

pnp

npn

20ms

k-1

k-2

pqa

dlh

sub

add

0.50

hold 0.01 99.99

0.01 0.50 99.99

0.01

99.99

ud-a

ud-b

ud-c

*1 If the mode is switched to the function setting mode during operation, operation will continue.

*2 Changes made to settings in function setting mode are enabled for the first time when the mode is changed to run mode. Also,

when settings are changed, the counter is reset (present value initialized and output turned OFF) on returning to run mode.

If the output time is 0.00,

hold is displayed.

Note: Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

Note: Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

(0.50 s) (99.99 s)

(0.01 s)

Twin Counter

Output 2

output

time

(OTM2)

Output 1

output

time

(OTM1)

0.50

0.01

99.99

(0.50 s) (99.99 s)

(0.01 s)

0.50

0.01

99.99

For details on operations and display in run mode, refer to page page 20.

The display depends on the selected configuration.

H7CX-R11W-N 데이터시트(PDF) 16 Page - Omron Electronics LLC

H7CX-R11W-N 데이터시트(HTML) 16 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

데이터시트 다운로드

링크 URL