| 전자부품 데이터시트 검색엔진 |
|
SC286 데이터시트(PDF) 15 Page - Semtech Corporation |
|
|
|||||||||||||||||||||||||||||
SC286 데이터시트(HTML) 15 Page - Semtech Corporation |
|
15 / 20 page ![]() SC286 To guarantee an operating junction temperature of less than 125°C, Figure 3 shows the maximum allowable total power loss versus temperature. The curve is based upon the junction temperature of either channel reaching a maximum of 125°C. Each channel of SC286 can support up to 4A load current. Figure 4 shows the maximum allowable power loss in channel B versus power loss in channel A for a range of temperatures. Ambient Temperature (°C) 2 2.5 3 3.5 4 4.5 25 35 45 55 65 75 85 95 105 VIN = 5V; VOUT = 1.2V VIN = 5V; VOUT = 3.3V VIN = 3.3V; VOUT = 1.2V Figure 3 — Maximum allowable total loss versus temperature for a maximum junction temperature of 125°C 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Power Loss of Channel A (W) TA = 55°C TA = 25°C TA = 70°C TA = 85°C Figure 4 — Maximum allowable power loss in channel B versus power loss in channel A for a range of temperatures (both channels same current) Applications Information (continued) Shut Down When all CTL pins for a channel are low, the device will run in shutdown mode, drawing less than 1μA from the input power supply. The internal switches and band-gap voltage will be immediately turned off. Thermal Shutdown The device has an independent thermal shutdown feature for each channel to protect the SC286 if the junction tem- perature exceeds 160°C. During thermal shutdown, the on-chip power devices are disabled, floating the LX output. When the temperature drops by 10°C, it will initi- ate a soft start cycle to resume normal operation. Under-Voltage Lockout Under-Voltage Lockout (UVLO) is enabled when the input voltage for each channel drops below the UVLO threshold. This prevents the device from entering an ambiguous state in which regulation cannot be maintained. Hysteresis of approximately 300mV is included to prevent chattering near the threshold. When the AVIN voltage rises back to the turn-on threshold and CTL X is high, the soft-start mode is initiated. Power Good The power good (PGOOD) for each channel is an open- drain output. When the output voltage for each channel drops below 10% of the nominal voltage, the PGOOD pin for that channel is pulled low after a 20μs delay. During start-up, PGOOD will be asserted 1.8ms (typ.) after the output voltage reaches 90% of the final regulation voltage. The faults of over voltage, fold-back current limit mode and thermal shutdown will force PGOOD low after a 20µs delay. When recovering from a fault, PGOOD will be asserted 2ms (typ.) after Vout reaches 90% of the final regulation voltage. 15 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |