REV. 0

AD1981A

–15–

VRA

Variable Rate PCM Audio Support: (read-only) This bit returns a “1” when read to indicate that variable rate

PCM audio is supported.

SPDIF

SPDIF Support: (read-only) This bit returns a “1” when read to indicate that SPDIF transmitter is supported (IEC958).

DSA[1:0]

DAC Slot Assignments: (read/write) (reset default = 00)

00 DACs 1, 2 = 3 and 4

01 DACs 1, 2 = 7 and 8

10 DACs 1, 2 = 6 and 9

11 DACs 1, 2 = 10 and 11

AMAP

Slot DAC mappings based on Codec ID: (read only)

This bit returns a “1” when read to indicate that slot/DAC mappings based on Codec ID is supported.

REV[1:0]

REV[1, 0] = 01 indicates Codec is AC ’97 revision 2.2-compliant (read-only).

ID[1:0]

Indicates Codec Configuration: (read-only)

00 = Primary

01, 10, 11 = Secondary

Extended Audio Status and Control Register (Index 2Ah)

*The extended audio status and control register is a read/write register that provides status and control of the extended audio features.

VRA

Variable Rate Audio: (read/write)

VRA = 0, sets fixed sample rate audio at 48 KHz (reset default).

VRA = 1, enables variable rate audio mode (enables sample rate registers and SLOTREQ signaling).

SPDIF

SPDIF Transmitter Subsystem Enable/Disable Bit: (read/write)

SPDIF = 1 enables the SPDIF transmitter.

SPDIF = 0 disables the SPDIF transmitter (default).

This bit is also used to validate that the SPDIF transmitter output is actually enabled. The SPDIF bit is only allowed

to be set high if the SPDIF pin (48) is pulled down at power-up enabling the Codec transmitter logic. If the

SPDIF pin is floating or pulled high at power-up, the transmitter logic is disabled and this bit therefore returns a low,

indicating that the SPDIF transmitter is not available. This bit must always be read back to verify that the SPDIF

transmitter is actually enabled.

SPSA[1:0]

SPDIF Slot Assignment Bits: (read/write) These bits control the SPDIF slot assignment and respective defaults,

depending on the Codec ID configuration.

SPCV

SPDIF Configuration Valid: (read-only) Indicates the status of the SPDIF transmitter subsystem, enabling the

driver to determine if the currently programmed SPDIF configuration is supported. SPCV is always valid, independent

of the SPDIF-enable bit status.

SPCV = 0 indicates current SPDIF configuration {SPSA, SPSR, DAC slot rate, DRS} is not valid (not supported).

SPCV = 1 indicates current SPDIF configuration {SPSA, SPSR, DAC slot rate, DRS} is valid (supported).

VFORCE

Validity Force Bit: (reset default = 0)

When asserted, this bit forces the SPDIF stream “Validity” flag (Bit 28 within each SPDIF L/R subframe) to be

controlled by the “V” bit (D15) in Register 3Ah (SPDIF control register).

VFORCE = 0 and “V” = 0; The “Validity” bit is managed by the Codec error detection logic.

VFORCE = 0 and “V” = 1; The “Validity” bit is forced high, indicating subframe data is invalid.

VFORCE = 1 and “V” = 0; The “Validity” bit is forced low, indicating subframe data is valid.

VFORCE = 1 and “V” = 1; The “Validity” bit is forced high, indicating subframe data is invalid.

Reg Num Name

D15

D14 D13 D12 D11

D10 D9 D8 D7 D6

D5

D4

D3

D2

D1 D0

Default

2Ah

Ext’d Audio Stat/Ctrl VFORCE

XXXX

SPCV XXXX SPSA1 SPSA0 X SPDIF X VRA

0000h