| 전자부품 데이터시트 검색엔진 |
|
A25GFM080QL 데이터시트(PDF) 17 Page - AMIC Technology |
|
|
|||||||||||||||||||||||||||||
A25GFM080QL 데이터시트(HTML) 17 Page - AMIC Technology |
|
17 / 58 page ![]() A25LQ080 Series (April, 2016, Version 1.0) 16 AMIC Technology Corp. Write Status Register (WRSR) The Write Status Register (WRSR) instruction allows new values to be written to the Status Register. Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded and executed, the device sets the Write Enable Latch (WEL). The Write Status Register (WRSR) instruction is entered by driving Chip Select ( S ) Low, followed by the instruction code and the data byte on Serial Data Input (DI). The instruction sequence is shown in Figure 6. Only non-volatile Status Register bits SRP0, SEC, TB, BP2, BP1, BP0 (bits 7, 6, 5, 4, 3, 2 of Status Register-1) and CMP, APT, QE (bits 14, 10 and 9 of Status Register-2) can be written. All other Status Register bits are always read as ‘0’ and will not be affected by the Write Status Register instruction. Chip Select ( S ) must be driven High after the eighth or sixteenth bit of the data byte has been latched in. If not, the Write Status Register (WRSR) instruction is not executed. If Chip Select ( S ) is driven high after the eighth clock the CMP and QE bits will be cleared to 0. As soon as Chip Select ( S ) is driven High, the self-timed Write Status Register cycle (whose duration is tW) is initiated. While the Write Status Register cycle is in progress, the Status Register may still be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Write Status Register cycle, and is 0 when it is completed. When the cycle is completed, the Write Enable Latch (WEL) is reset. The Write Status Register (WRSR) instruction allows the user to change the values of the Block Protect (APT, CMP, SEC, TB, BP2, BP1, BP0) bits, to define the size of the area that is to be treated as read-only, as defined in Table 1. The Write Status Register (WRSR) instruction also allows the user to set the Status Register Protect (SRP0) bit. Those bits are used in conjunction with the Write Protect ( W ) pin to disable writes to the Status Register. Factory default for all Status Register bits are 0. Figure 6. Write Status Register (WRSR) Instruction Sequence 8 9 2 3 4 5 6 7 810 911 12 13 14 15 MSB High Impedance Instruction (01h) 01 2 3 4 5 6 7 0 1 S 16 17 18 19 20 21 22 23 Status Register In C 15 14 13 12 11 10 DI DO Table 5. Protection Modes SRP0 W Status Register Description 0 X Software Protection Status Register is Writable (if the WREN instruction has set the WEL bit). The values in the CMP, APT, SRP0, SEC, TB, BP2, BP1, BP0 bits can be changed. 1 0 Hardware Protection Status Register is hardware write protected. The values in the CMP, APT, SRP0, SEC, TB, BP2, BP1, BP0 bits cannot be changed. 1 1 Software Protection When W pin is high. Status Register is Writable (if the WREN instruction has set the WEL bit). The values in the CMP, APT, SRP0, SEC, TB, BP2, BP1, BP0 bits can be changed. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |