| 전자부품 데이터시트 검색엔진 |
|
OPA111AM 데이터시트(PDF) 8 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
OPA111AM 데이터시트(HTML) 8 Page - Texas Instruments |
|
8 / 14 page ![]() 8 OPA111 ® TYPICAL PERFORMANCE CURVES (CONT) TA = +25°C, VCC = ±15VDC unless otherwise noted. APPLICATIONS INFORMATION OFFSET VOLTAGE ADJUSTMENT The OPA111 offset voltage is laser-trimmed and will require no further trim for most applications. As with most amplifi- ers, externally trimming the remaining offset can change drift performance by about 0.3 µV/°C for each 100µV of adjusted offset. Note that the trim (Figure 1) is similar to operational amplifiers such as 741 and AD547. The OPA111 can replace most other amplifiers by leaving the external null circuit unconnected. INPUT PROTECTION Conventional monolithic FET operational amplifiers require external current-limiting resistors to protect their inputs against destructive currents that can flow when input FET gate-to-substrate isolation diodes are forward-biased. Most BIFET amplifiers can be destroyed by the loss of –VCC. FIGURE 1. Offset Voltage Trim. FIGURE 2. Input Current vs Input Voltage with ±V CC Pins Grounded. Unlike BIFET amplifiers, The Difet OPA111 requires input current limiting resistors only if its input voltage is greater than 6V more negative than –VCC. A 10kΩ series resistor will limit input current to a safe level with up to ±15V input levels, even if both supply voltages are lost. Static damage can cause subtle changes in amplifier input characteristics without necessarily destroying the device. In precision operational amplifiers (both bipolar and FET types), this may cause a noticeable degradation of offset voltage and drift. Static protection is recommended when handling any precision IC operational amplifier. GUARDING AND SHIELDING As in any situation where high impedances are involved, careful shielding is required to reduce “hum” pickup in input leads. If large feedback resistors are used, they should also be shielded along with the external input circuitry. Leakage currents across printed circuit boards can easily exceed the bias current of the OPA111. To avoid leakage problems, it is recommended that the signal input lead of the OPA111 be wired to a Teflon standoff. If the OPA111 is to be soldered directly into a printed circuit board, utmost care must be used in planning the board layout. A “guard” pattern INPUT OFFSET VOLTAGE CHANGE DUE TO THERMAL SHOCK 150 75 0 –75 –150 Time From Thermal Shock (Minutes) –1 012345 25°C 85°C BM AM T A = 25°C to TA = 85°C Air Environment OPA111 2 3 7 4 5 1 6 –V CC +V CC 10k Ω to 1M trim potentiometer (100k Ω recommended). ±10mV typical trim range. V I IN Maximum Safe Current Maximum Safe Current –15 Input Voltage (V) –10 –5 0 5 10 15 2 1 0 –1 –2 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |