SST25PF080B datasheet(12/32 Pages) MICROCHIP

12 / 32 page

SST25PF080B

DS20005137B-page 12

 2014 Microchip Technology Inc.

4.5.7

4-KBYTE SECTOR-ERASE

The Sector-Erase instruction clears all bits in the

selected 4 KByte sector to FFH. A Sector-Erase

instruction applied to a protected memory area will be

ignored. Prior to any Write operation, the Write-Enable

(WREN) instruction must be executed. CE# must

remain active low for the duration of any command

sequence. The Sector-Erase instruction is initiated by

executing an 8-bit command, 20H, followed by address

bits [A23-A0]. Address bits [AMS-A12] (AMS = Most Sig-

nificant address) are used to determine the sector

address (SAX), remaining address bits can be VIL or VIH.

CE# must be driven high before the instruction is exe-

cuted. The user may poll the Busy bit in the software

status register or wait TSE for the completion of the

internal self-timed Sector-Erase cycle. See Figure 4-10

for the Sector-Erase sequence.

FIGURE 4-10:

SECTOR-ERASE SEQUENCE

4.5.8

32-KBYTE AND 64-KBYTE BLOCK-

ERASE

The 32-KByte Block-Erase instruction clears all bits in

the selected 32 KByte block to FFH. A Block-Erase

instruction applied to a protected memory area will be

ignored. The 64-KByte Block-Erase instruction clears all bits

in the selected 64 KByte block to FFH. A Block-Erase

instruction applied to a protected memory area will be

ignored. Prior to any Write operation, the Write-Enable

(WREN) instruction must be executed. CE# must remain

active low for the duration of any command sequence.

The 32-KByte Block-Erase instruction is initiated by

executing an 8-bit command, 52H, followed by address

bits [A23-A0]. Address bits [AMS-A15] (AMS = Most Sig-

nificant Address) are used to determine block address

(BAX), remaining address bits can be VIL or VIH. CE#

must be driven high before the instruction is executed. The

64-KByte Block-Erase instruction is initiated by executing an

8-bit command D8H, followed by address bits [A23-A0].

Address bits [AMS-A16] are used to determine block address

(BAX), remaining address bits can be VIL or VIH. CE# must

be driven high before the instruction is executed. The user

may poll the Busy bit in the software status register or wait

TBE for the completion of the internal self-timed 32-

KByte Block-Erase or 64-KByte Block-Erase cycles.

See Figures 4-11 and 4-12 for the 32-KByte Block-

Erase and 64-KByte Block-Erase sequences.

FIGURE 4-11:

32-KBYTE BLOCK-ERASE SEQUENCE

CE#

SCK

ADD.

01 2 3 4 5 6 7 8

ADD.

HIGH IMPEDANCE

15 16

23 24

MODE 0

MODE 3

25137 SecErase.0

MSB

CE#

SCK

ADDR

01 2 3 4 5 6 7 8

ADDR

HIGH IMPEDANCE

15 16

23 24

MODE 0

MODE 3

25137 32KBklEr.0

MSB

SST25PF080B 데이터시트(PDF) 12 Page - Microchip Technology

SST25PF080B 데이터시트(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

데이터시트 다운로드

링크 URL