| 전자부품 데이터시트 검색엔진 |
|
ELM329LP 데이터시트(PDF) 68 Page - ELM Electronics |
|
|
|||||||||||||||||||||||||||||
ELM329LP 데이터시트(HTML) 68 Page - ELM Electronics |
|
68 / 87 page ![]() ELM329L 68 of 87 ELM329L DSA Elm Electronics – Circuits for the Hobbyist www.elmelectronics.com Programmable Parameter Summary (continued) PP Description Values Default Type 24 CAN auto formatting (AT CAF default setting) D 25 D CAN filler byte (used to pad out messages) 00 CAN auto flow control (AT CFC default setting) 00 (ON) 00 (ON) 00 to FF 00 = ON FF = OFF 00 = ON FF = OFF 26 D 20 Default (Single Wire) Transceiver Mode M0 - M1 pin setting during normal CAN operation (see page 25) 03 (normal) 00 to 03 D 21 Default CAN Silent Monitoring setting (for AT CSM) R FF (ON) FF = ON 00 = OFF 22 CAN wakeup message rate (AT SW default setting) setting = value x 20.48 msec 00 to FF 62 (2.0 sec) D 00 to 02 D 23 Default Wakeup Mode (AT WM setting) 00 (OFF) 0F F8 (11111000) 00 to FF More Power Control options Each bit of this byte controls an option, as follows: b7: Auto LP (CAN) control 0: disabled 1: enabled allows low power mode if the CAN activity stops b6: Auto LP (CAN) timeout 0: 2 mins 1: 10 mins no CAN activity timeout setting b5: Auto LP (CAN) warning 0: disabled 1: enabled if enabled, says ‘ACT ALERT’ 1 minute before timeout b4: Active LED 0: off 1: flashes setting during low power, if there was CAN activity on pin 11 b3: Previous CAN 0: required 1: ignored wakeup on CAN activity may be set to require that there was CAN activity prior to going to low power mode b2: reserved for future - leave set at 0 b1: reserved for future - leave set at 0 b0: Control output 0:normal 1:CAN Monitor if set to 1, the Control (pin 4) output follows CAN activity (Control is a high level when there is CAN activity detected) R 28 FF (11111111) 00 to FF D CAN Filter outputs (controls CAN sends while searching) The bits of this byte control options, as follows: b7: 500 kbps match 0: ignored 1: required b6: 250 kbps match 0: ignored 1: required b5 to b1: reserved for future - leave set to 1 b0: send if bus is quiet 0: not allowed 1: allowed |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |